Low voltage in the evening: what it does to your fridge, AC, pump, fans and battery, and what fixes it
Sashikesh Kumar, Diploma in Electrical · checked against V-Guard's own sheets, 12 Nov 2026
The short answer
Measure at 7–9 pm
Free fixes + complaint
Fridge stabiliser
AC stabiliser
Mainline stabiliser
Thicker main wire
Low voltage slowly wears out the things with a compressor or a motor: fridge, AC, water pump. Fans only slow down and heaters only heat slower. Take two readings first, one at the main board and one in the farthest room, so you pay for the right fix. A stabiliser protects what is behind it. Only NBPDCL can make the lane stronger.
230 V
Declared supplyThe rules allow 6% either side: about 216 to 244 V.
7–9 pm
When to measureAt the main board and in the farthest room, usual load on.
90 V
VGMW 500 Plus works fromV-Guard's 15 A mainline stabiliser. Below that it cuts off.
A summer day at a socket in Muzaffarpur
A drawing of the usual pattern, not one house's readings: your lane's numbers will differ, which is why you measure. Limits: 230 V ± 6% from the supply rules; 180 V from V-Guard's Prime 1100 inverter specification; 170 V and 250 V from V-Guard's stabiliser guide and FAQ.
What it does to each thing
Compressors and motors get hurt. Fans and heaters just get weak.
The rule of thumb: anything that has to start a motor against a load suffers most. Find what you own below.
Fridge
Damage risk: high
The compressor works harder at low voltage, heats up, and may fail to start and keep retrying. It runs day and night, so it takes the most punishment. V-Guard gives 170–290 V as the range of modern fridges and 200–240 V for older ones.
You notice: clicking on and off, weak cooling, ice soft by morning.
Protect it: a fridge stabiliser with low cut-off and a time delay. Never a TV stabiliser (V-Guard says so plainly).
AC, 1 or 1.5 ton
Damage risk: high
The compressor strains, trips on its own protection, or does not start at all. The AC that cools fine at noon cools poorly at 8 pm. An inverter AC copes only inside the voltage band printed in its manual.
You notice: AC stops and starts, slow cooling, outdoor unit humming.
Protect it: its own stabiliser on its own line. Inverter AC: read its band first.
Water pump
Damage risk: high
A motor's pulling force falls with the square of the voltage (a standard figure): at 180 V it has about 60% of its normal pull. It draws more current to do the same work, so the winding heats. Starting already takes 2 to 3 times the running power, V-Guard notes.
You notice: humming, slow water, motor too hot to touch, burnt winding in the end.
Protect it: run it in the morning. If it hums without turning, switch it off at once.
Fans and coolers
Damage risk: low
Speed falls with the voltage, by the same square rule, so every fan in the lane slows at the same hour. Running a fan at full regulator for hours on very low voltage does make the motor run warm.
You notice: all fans slow together, regulator at 5 feels like 2.
Helps: a mainline stabiliser, or a BLDC fan. New capacitors in every fan do not. Fan speed in low voltage.
Inverter and battery
Damage risk: medium
The charger gets less to work with, so the battery fills slowly. Worse: in UPS mode the V-Guard Prime 1100 accepts only 180–260 V. Below 180 V it leaves the mains and runs the house on battery, so the battery is already flat when the real cut comes. Normal mode accepts 90–290 V.
You notice: inverter clicking to battery every evening, short backup at night.
An LED bulb dims or flickers near the bottom of the range printed on its box. An old choke tube light may not start at all. V-Guard gives LED and LCD TVs a 90–290 V working range: they suffer more from high voltage and spikes than from low.
You notice: lights dim together, flicker when the fridge or pump starts.
Read the range on the bulb box. Flicker only when a motor starts: light flicker.
Geyser, iron, room heater
Damage risk: low
A heating element is not harmed by low voltage. Its power falls with the square of the voltage (standard figure), so at 180 V a 2,000 W geyser gives about 1,200 W and takes much longer.
You notice: water takes ages to heat, iron stays lukewarm.
Run them outside 7–9 pm. That helps your own voltage and the whole lane's.
Measure before you buy
Two readings tell you whose problem it is
A plug-in voltmeter is enough. We can order one for you, or use the display of a stabiliser you already have.
Reading A, at the board. On a normal evening between 7 and 9 pm, with fans, lights and the fridge on as usual, plug the meter into the socket nearest the main board.
Reading B, in the farthest room. Straight after, plug it into a socket in the room farthest from the board.
Repeat for three evenings, and once at 11 am. Write the date, time and both readings on paper. You need these for a complaint.
Watch it while a motor starts. Switch on the pump or the iron while you look at the meter. A sharp dip that recovers when it stops means a weak wire or joint on that line.
What you read
What it means, what to do
A low, B about the same
The lane's supply is low. Protect the costly things, and complain to NBPDCL.
A fine (216 V or more), B lower by more than about 7 V
Volts are lost inside your house: a loose joint or a thin, long wire. Electrician first. (Usual practice keeps the drop inside a house to about 3%, some 7 V.)
A low, and B much lower
Both. Fix the wiring first because it is cheaper, then measure again.
Readings jump; lights get brighter when something heavy starts; or one socket above 250 V while lights elsewhere dim
Possible loose neutral. This is a danger sign. Switch off heavy things and call an electrician today. If neighbours see it too, call 1912 at once.
Where to take the two readings
Reading A tells you about the supply. The gap between A and B tells you about your own wiring. The cable from the pole to the meter is NBPDCL's to fix.
Read your numbers
Put in your two readings
We mark them against the limits the makers publish and tell you which fix fits. Nothing leaves this page unless you press WhatsApp.
What your readings say
Put in reading A to start
Reading A alone tells you about the supply. Add B to see whether your own wiring is losing volts too.
Sashikesh replies with what to fit for your fridge, AC and pump, with today's price. Add your fridge litres, AC tonnage and pump HP to the message.
The fixes, cheapest first
Do the free things this week. Then buy only what your readings call for.
Free, or nearly this week
Move heavy loads out of 7–9 pm. Pump in the morning, iron and geyser outside the peak. Each one you move lifts your own voltage and the lane's.
Get the joints tightened. A hot or brown switch, socket or MCB terminal is losing volts and can burn. An hour's work for an electrician. See switch sparking, socket heating.
Check the inverter's mode. If it clicks onto battery every evening, it is in UPS mode (Prime 1100: 180–260 V). Normal mode accepts 90–290 V, so the battery keeps charging and is full for the real cut. The trade-off: in normal mode your fans and lights get the low mains voltage instead of steady battery power.
Complain to NBPDCL if reading A is low. Helpline 1912 or 1800 202 2813, or the Suvidha app. Give your consumer number, lane, the transformer or pole number and your written readings, and keep the complaint number. An overloaded transformer is theirs to fix. Contacts: Muzaffarpur bijli office.
1Fridge stabiliser
When: no mainline stabiliser, or cuts come often
It must have low and high voltage cut-off and a time delay. V-Guard puts that delay at 2–4 minutes, so the compressor settles before power returns after a cut.
Never a TV stabiliser on a fridge: it has only high-voltage cut-off and no delay (V-Guard FAQ).
A fridge sold as "stabiliser-free" still needs one where voltage falls this low, V-Guard says, and fridge makers' warranty terms ask for it.
We order it for you: tell us the fridge's litres on WhatsApp and ask for the time it takes. Stabilisers
2AC stabiliser
When: every 1 or 1.5 ton AC, on its own line
V-Guard's buying guide lists its 1.5-ton AC stabilisers at 2,700–3,000 VA. A 1-ton AC can use the same.
They come with different working ranges: from 90, 130, 150 or 170 V upward. Pick one whose lower figure is below your worst evening reading.
We order it for you: tell us the AC's tonnage and model.
3Mainline: V-Guard VGMW 500 Plus
When: fans, lights, TV, fridge and pump all suffer together
15 Acapacity
90–300 Vinput range
2 yearswarranty
5 ± 2 sstart delay
Low + highcut-off
Metalbody
15 A at 230 V is about 3.4 kVA (standard figure). Keep V-Guard's own 20–25% margin and plan for about 12 A running: lights, fans, TV, fridge and a 0.5 HP pump.
The AC stays off it, on its own line and stabiliser (step 2). An AC plus the rest of the house is more than 15 A.
Wired after the main MCB and before the distribution board, with a short, thick wire.
Its 5-second delay is a start delay, not the 2–4 minute compressor delay V-Guard asks for on a fridge. If cuts are frequent, keep a fridge unit with delay as well.
When: reading B stays well below A after the joints are tightened
Copper wire loses volts over distance, there and back. With 10 A flowing (a fridge, fans, lights and a pump together):
Copper wire
15 m run
30 m run
1.5 sq mm
4.0 V
8.0 V
2.5 sq mm
2.4 V
4.8 V
4 sq mm
1.5 V
3.0 V
6 sq mm
1.0 V
2.0 V
Worked out from IS 8130's maximum resistance for flexible copper at 20°C (standard figure). A hot wire loses a little more; one loose joint can lose more than all of this.
The main run from meter to board is sized to your sanctioned load: a 4 or 6 sq mm run is usual practice. See meter and load and wire amps chart.
The cable from the pole to the meter is NBPDCL's. If it is old, thin or jointed, put that in the complaint.
Where each fix goes
Numbers match the steps on this page. The AC never goes through the 15 A mainline. Everything before the meter is NBPDCL's to fix.
What does not help
A stabiliser cannot make the lane stronger. To lift 160 V up towards 230 V it pulls more current from the same weak line. Below its cut-off (90 V for the VGMW 500 Plus) it switches off.
New capacitors or a bigger regulator in every fan. If all fans slow together, the supply is the cause.
A TV stabiliser on the fridge. No low cut-off, no time delay.
The AC through the mainline with the rest of the house. It is more than 15 A together.
Running a humming motor "until it picks up". That is how windings burn.
Never complaining. A transformer that is low every evening gets upgraded only when NBPDCL has the complaints on record.
For this job
What we supply for low voltage
Stabilisers
Prices are from our latest bill and change often. Please confirm today's rate on WhatsApp or call before buying.
Anything not on the shelf, such as a plug-in voltmeter, a BLDC fan or a particular stabiliser model, we can order for you: ask on WhatsApp for the time it takes. BLDC or normal fan: the comparison.
Questions people ask us
Short answers
Why does the voltage drop at home in the evening? (ghar mein low voltage kyon)
Between about 6 and 10 pm every house on the same transformer runs fans, coolers, lights and ACs together. The transformer and the long lines from it are stretched, so the houses at the far end get the lowest voltage. Inside the house, a loose joint or a thin, long wire takes off a few more volts.
Is a stabiliser necessary in low voltage?
For the fridge and the AC, yes, if your evening reading falls below their range. V-Guard gives 170–290 V for modern fridges and 200–240 V for older ones. For the whole house, a mainline stabiliser like the VGMW 500 Plus (15 A, works from 90 V) helps when many things suffer. Measure first.
Does low voltage damage a fridge or AC?
Over time, yes. The compressor works harder, runs hot, and may fail to start and keep retrying. Fans and heaters are not damaged in the same way: they only get slower or weaker.
How do I check the voltage at home?
Plug a voltmeter into a socket next to the main board between 7 and 9 pm with the usual load on, then into a socket in the farthest room. Write both readings and the time, for three evenings. The first reading tells you about the supply; the difference tells you about your house wiring. Put them into the reading checker above.
Whole-house stabiliser, or separate ones for the fridge and AC?
Each AC gets its own stabiliser in any case, because an AC with the rest of the house is more than a 15 A mainline carries. If only the fridge worries you, a fridge stabiliser is cheapest. If fans, lights, TV, fridge and pump all suffer, fit a mainline VGMW 500 Plus after the main MCB. More: whole house or fridge and AC.
Where do I complain about low voltage in Muzaffarpur?
To NBPDCL, which supplies Muzaffarpur: helpline 1912 or 1800 202 2813, or the Suvidha app. Give your consumer number, lane, the transformer or pole number and your written readings, and keep the complaint number. Office details: Muzaffarpur bijli office.
Does a stabiliser give a fixed 230 V?
No. V-Guard's own answer is that a stabiliser keeps the output inside a safe band, stepping up or down with relays as the input moves. It does not hold one fixed figure, and it switches the load off when the input goes outside its range.
Lights go very bright late at night. Is that a problem too?
Yes. When the lane switches off, the voltage can swing high. V-Guard says some electronics misbehave above 250 V and equipment can be harmed above 270 V. A stabiliser's high cut-off handles this. If it happens while other rooms are dim at the same moment, suspect a loose neutral and call an electrician.
Sashikesh Kumar
Diploma in Electrical, Tashya Ventures
Looks after wiring, fans, inverters, stabilisers and pumps at our Reva Road store, Muzaffarpur. Every maker figure on this page was checked against V-Guard's own pages on 12 Nov 2026. Where a number is a standard engineering figure rather than a maker's, the page says so.
Where the numbers come from
V-Guard, VGMW 500 Plus mainline stabiliser: 15 A, 90–300 V input, 5 ± 2 s initial delay, low and high voltage cut-off, metal cabinet, 2-year warranty.
V-Guard, stabiliser FAQ: output kept within a band; no TV stabiliser on a fridge; fridge time delay 2–4 minutes; "stabiliser-free" fridges still need one; above 250 V some electronics misbehave, above 270 V equipment can be harmed; LED/LCD TVs 90–290 V.
V-Guard, buying guide for voltage stabilisers: 230 V standard supply; fridges 170–290 V (modern), 200–240 V (older); 1.5-ton AC models 2,700–3,000 VA with ranges from 90, 130, 150 or 170 V; 20–25% sizing margin.
V-Guard, Prime 1100 inverter specification (also in V-Guard's inverter brochure): mains input 90–290 V in normal mode, 180–260 V in UPS mode.
Indian Electricity Rules 1956, rule 54, carried into the Central Electricity Authority's supply regulations: declared low voltage not to vary by more than 6%.
Standard figures: IS 8130 maximum conductor resistance for flexible copper (1.5 sq mm 13.3, 2.5 sq mm 7.98, 4 sq mm 4.95, 6 sq mm 3.30 ohm per km at 20°C); motor pull and heater power vary with the square of the voltage.
Send us your evening readings
Readings A and B with the time, your fridge litres, AC tonnage and pump HP. We'll tell you what to fit, with today's price, on WhatsApp.