हिंदी Call90310 74624
Home›Roofing sheets›12 feet
Roofing sheet size · 12 ft

12 feet (3.6 m) cement roofing sheet: price, weight, and how to fix it so it does not crack

The short answer

The "12 feet" cement sheet (asbestos sheet, in most people's words) is 3.6 m long, which is 11.8 ft, about 1.05 m wide and 6 mm thick. It weighs about 45 kg, so it takes two people to lift and a vehicle at least as long as the sheet to bring. A frame of three purlins is not enough for it: it needs four.

45 kg
One sheetCharminar's own 12.3–12.7 kg per metre × 3.6 m. Plan for 47 kg.
4
Purlin linesNo gap wider than 1.4 m. Three purlins leave gaps of 1.6 m.
3.5 m²
Roof one sheet coversAfter the laps (Everest's 1.01 m cover width). About 37 sq ft.

Online sellers quote cement sheets per metre. Multiply by 3.6 to get one 12 ft sheet, and ask whether GST is added on top. Our price is per sheet, with GST bill: today's sheet rate.

One 12 ft sheet, side view of the slope
One 12 ft sheet on three and on four purlinsSide view along the slope. With four purlin lines the gaps are about 1.07 metres, inside the 1.4 metre limit. With three purlin lines the gaps are 1.6 metres, too wide.Right: 4 purlin lineseaveridge0.3 m1.07 m1.07 m1.07 m0.1 mEvery gap about 1.07 m: under the 1.4 m limitWrong: 3 purlin lineseaveridge0.3 m1.6 m1.6 m0.1 mGaps of 1.6 m: over 1.4 m, cracks at the middle
Drawn flat along the slope so the gaps can be read. A 3.6 m sheet with 0.3 m hanging over the eave and its top end 0.1 m from the ridge purlin leaves 3.2 m between the first and last purlin. Three gaps of 1.07 m fit under the 1.4 m limit; two gaps of 1.6 m do not.
Size and weight

What "12 feet" really is

Nobody makes a sheet of exactly 12 ft. The sheet the shops call 12 ft is the 3.6 m sheet, which is 11.8 ft. Everest lists 3.6 m in its fibre cement range, and Charminar (BirlaNu) makes lengths from 1 m to 4.25 m. It is our longest sheet and the one with the least waste on a small shed whose slope is about 10 to 11 ft.

Figure12 ft (3.6 m) sheet
Length3.6 m11.8 ft
Width, edge to edge1.05 mEverest and Charminar both
Width when laid1.01 mEverest's cover width. Charminar says 91% cover on a 3 m sheet, which is the same thing.
Thickness6 mmCharminar's page. Everest's span figures are "for 6 mm".
Wave: spacing and depth146 / 48 mmCharminar's page
Weight44–46 kg12.3–12.7 kg per metre × 3.6 (Charminar). See the box below.
Minimum end lap150 mmEverest and IS 3007
Where the makers disagree: the weightCharminar prints 12.3–12.7 kg per metre, so 44–46 kg for 3.6 m. Everest does not print a weight for its standard 3.6 m sheet at all. Its Hi-Tech brochure gives 13.00 kg per metre (its web page says 12.44), which would be 47 kg for 3.6 m, but Hi-Tech is made only up to 3.0 m. We plan with the higher figure, 47 kg, for lifting and for the load on a vehicle. The side lap also differs: Everest's table says 44 mm, its picture caption says 40 mm, its Hi-Tech brochure says 50 mm. Lay the sheets as the maker's cover width says and keep the larger lap if you are unsure.
Size of the sheet and its wave
Size of a 12 ft cement sheetPlan of the sheet: 3.6 m long, 1.05 m wide, 1.01 m when laid, with end lap and side lap marked. Below, the wave profile: 146 mm between crests, 48 mm deep, 6 mm thick.Seen from above3.6 m (11.8 ft)end lap 150 mmside lap1.05 mlaid width 1.01 m(Everest)Seen from the end146 mm48 mm6 mm thick
Top: the sheet seen from above. The yellow strip is the end lap where the next sheet up the slope sits on top. The red strip is the side lap. Bottom: the wave seen from the end, with the figures printed on Charminar's page.
The frame

Why a 12 ft sheet needs four purlins, not three

A 6 mm sheet may not span more than 1.4 m between purlins (IS 3007 Part 1, Everest's fibre cement page and its Hi-Tech brochure agree). The same code lets the sheet hang over the eave by no more than 0.3 m and puts the ridge purlin 75 to 115 mm from the apex. Now do the sum for a 3.6 m sheet.

1Three purlins

0.3 m overhang + 1.4 m + 1.4 m + 0.1 m at the ridge = 3.2 m. The sheet is 0.4 m longer than that, so the gaps become 1.6 m. Too wide: the sheet flexes and cracks at the middle purlin, usually in the first storm.

2Four purlins

The same 3.2 m split in three gives gaps of about 1.07 m. Well inside 1.4 m. This is the frame a 12 ft sheet wants.

3Why 10 ft sheets need only three

A 10 ft sheet is 3.0 m, and 0.3 + 1.4 + 1.4 + 0.1 = 3.2 m is enough for it. Three purlin lines carry a sheet up to about 3.1 m, no more. If your frame is already built with three, use 10 ft sheets.

When one sheet fits: the sheet you need is the slope length from eave to ridge plus about 0.2 m of drip over the eave (usual practice, the code allows up to 0.3 m). A slope of 3.0 to 3.4 m, which is 10 to 11 ft, takes one 12 ft sheet from eave to ridge, with no end lap across the roof where rain could get in. A longer slope needs two rows, the top row lapped at least 150 mm over the bottom one, and the lap must sit on a purlin. Everest's Hi-Tech brochure gives a minimum roof slope of 10 degrees; keep to that for any cement sheet.

Lifting and stacking

A 45 kg sheet, 3.6 m long: how to carry and store it

At 3.6 m the sheet is long and thin, and it bends under its own weight if you hold it flat. A bent sheet gets hairline cracks you cannot see, and the crack opens after the first rains. This is what we do and tell customers:

Carry it on its long edge, two people

  • One person at each end, sheet standing on its long edge. That is about 23 kg each.
  • Never carry it flat, never drag it, and never let it drop onto the ground: IS 3007 asks for lifting "avoiding impacts". Fibre-cement makers abroad give the same advice (BRANZ, New Zealand: carry sheets on edge).

Stack it properly if it waits

  • Level, firm ground with timber packing under the sheets, as in the drawing. IS 3007 says not higher than 1 m.
  • All the same size together. Damaged sheets in a separate pile, so nobody fits a cracked one.
  • Up-lap side on one side, down-lap side on the other, never mixed.
  • If the stack will stand in the open for long, cover it from the sun: IS 3007 warns that a stack heated on one side can crack.

Bringing it to your site

  • The vehicle body has to carry the 3.6 m sheets flat and supported along their length. Sheets hanging out over the tailgate snap on the first bump (usual practice).
  • Ten sheets are about 470 kg, twenty about 940 kg. Tell us the number of sheets and your site, and we give the delivery amount. Delivery and unloading are charged separately from the sheet price: how we load and deliver sheets · delivery rates.
Carrying a 12 ft sheet
Carrying a 12 ft sheetRight: two people carry the sheet standing on its long edge, one at each end, about 23 kilograms each. Wrong: one person carries it flat, the ends droop and the sheet cracks.Right: on edge, two peoplelong edge downabout 23 kgabout 23 kgWrong: flat, one personheld flat in the middleends droop, sheet cracks
Right way: on edge, one person at each end. Wrong way: flat, held in the middle. The ends drop and the sheet cracks.
Stacking sheets on site
Stack of sheets on timberSheets stacked on timber packing on level ground, no higher than 1 metre.not higher than 1 mSame size together, on level groundUp-lap one side, down-lap the othertimber packing under the stack
The stack is drawn with fewer sheets than a real one so the labels fit. The limit is 1 m of height, whatever the number of sheets.
Fixing

Where to drill, which bolt, where to stand

Most cracked sheets on a roof were broken by the person fixing them, not by the weather. These rules come from IS 3007 Part 1, the Indian code for laying corrugated cement sheets, and from Everest's installation guide.

Cutting and drilling

  • Cut on the ground, with a hand saw, outdoors, and keep the dust low. Wear a mask (usual practice).
  • Drill the hole. Never punch it. Punching splays the sheet and starts a crack (IS 3007).
  • Hole 2 mm bigger than the bolt, through the crown (the top of the wave), never the valley, and at least 75 mm from the sheet edge.
  • Mark the holes with the sheet lying in its final place on the purlins, then drill.

Bolts and washers

  • J-bolt (hook bolt) with a galvanised washer and a black bitumen washer under it, nut on top. Tighten only until the bitumen washer is seated. More than that cracks the crown.
  • Have the ridge pieces, bolts and washers on site before the first sheet goes up. If one is missing, the day is lost: ridge, hook bolts and washers.

On the roof

  • Never step on the sheets. Work from planks at least 375 mm wide laid across the purlins (IS 3007).
  • Start laying from the end away from the wind that brings the rain, so the side laps face away from it (IS 3007, Everest).
  • Stop work in high wind.
One fixing, in section
One fixing in sectionA J-bolt through a hole in the crown of the wave, with a galvanised washer and a bitumen washer on top, hooked under the purlin.purlin1234Section through one wave, at a purlin
  1. 1Nut, galvanised washer, bitumen washer sitting on the crown.
  2. 2Hole through the crown, 2 mm bigger than the bolt. Drilled, not punched.
  3. 3The J-bolt hooks under the purlin.
  4. 4Purlin. The sheet rests on it in the valley.
How many 12 ft sheets

Your roof, in numbers

Measure the slope from the wall edge to the ridge, and the length of the roof along the ridge. Both in feet. The sheet width used is Everest's 1.01 m cover.

This counts one plain slope. For a roof with two slopes, use the figures for one slope and double the answer. For ridges, bolts and washers as well, use the roofing sheet calculator.

For this slope

Sheet length you need–
Sheets across the roof–Roof length ÷ 1.01 m cover, rounded up.
12 ft sheets in all–
Purlin lines under one slope–No gap wider than 1.4 m.
Weight to carry and deliver–At 47 kg a sheet.
Cost of the sheetsAsk ratePrice per sheet on the rate page.
Ask for today's price on WhatsApp
Sheets are counted from the cover width, so add one for breakage and cutting if your roof is cut at hips or valleys.
Which 12 ft sheet

Everest or Charminar, and the asbestos question

Everest

The standard fibre cement sheet (CBS) is listed in 3.6 m. Cover width 1.01 m, 91% cover on a 3 m sheet, 150 mm end lap, purlins at most 1.4 m.

  • Everest's own picture caption for this sheet reads "Asbestos Fibre Cement". Its page body only says "fibre cement".
  • Everest's non-asbestos sheet, Hi-Tech (PVA fibre), is made only up to 3.0 m. There is no 12 ft Hi-Tech.
Everest sheets

Charminar (BirlaNu)

Fibre cement, 1050 mm wide, 6 mm, lengths 1 to 4.25 m, 12.3–12.7 kg per metre, IS 459. Its page prints no asbestos statement.

  • BirlaNu describes its Fortune line as the asbestos-free one. If you want that line in 12 ft, ask us.
  • Charminar prints the most complete wave figures, which is why the drawing on this page uses them.
Charminar sheets

Which one to take: both are 6 mm sheets of the same size, so the frame and the fixing are the same. Rate, name on the sheet and what is in stock decide it. For the full comparison read Everest or Charminar. If you need a non-asbestos 12 ft sheet, we can order it for you; ask on WhatsApp for the time it takes.

On our shelf for this job

12 ft sheets and what goes with them

Other lengths: 6 ft · 8 ft · 10 ft. Every size can be ordered; ask on WhatsApp for the time it takes. Today's price: sheet rates.

Questions people ask us

Short answers

What is the price of a 12 feet cement sheet in Muzaffarpur?

Our price per 12 ft (3.6 m) sheet, for Everest and Charminar, is on the sheet rate page, with a GST bill. Sellers online usually quote per metre: multiply by 3.6 for one sheet and ask whether GST is extra.

Is a 12 ft sheet really 12 feet?

No. It is the 3.6 m sheet, which is 11.8 ft. That is the longest sheet in Everest's fibre cement list, and Charminar makes it within its 1 to 4.25 m range.

How much does a 12 ft cement sheet weigh?

About 45 kg. Charminar prints 12.3 to 12.7 kg per metre, which gives 44 to 46 kg for 3.6 m. Everest does not print a weight for its standard sheet; its Hi-Tech brochure's 13.00 kg per metre would give 47 kg, so we plan with 47 kg.

How many purlins does a 12 ft sheet need?

Four. A 6 mm sheet can span at most 1.4 m between purlins, and with 0.3 m over the eave and the ridge purlin near the top, a 3.6 m sheet needs three gaps of about 1.07 m. Three purlins would leave gaps of 1.6 m.

Can one person carry a 12 ft cement sheet?

Not safely. It weighs about 45 kg and is 3.6 m long, so it bends if carried flat. Two people, one at each end, carry it on its long edge.

How much roof does one 12 ft sheet cover?

With another row lapped on top, about 3.48 m² (1.01 m cover width × 3.45 m after a 150 mm end lap), around 37 sq ft. A single sheet running from eave to ridge, with no end lap, covers up to 3.64 m².

Is the 12 ft asbestos sheet asbestos-free?

Everest's standard 3.6 m sheet is captioned "Asbestos Fibre Cement" in the maker's own picture. Everest's non-asbestos Hi-Tech sheet is made only up to 3.0 m. BirlaNu's page for Charminar states nothing either way, and it describes its Fortune line as asbestos-free. Ask us and we will tell you what the sheet you are buying is.

Is delivery included in the sheet price?

No. Delivery and unloading are charged separately, for sheets as for cement and sariya. Send your site and the number of sheets on WhatsApp and we give you the amount. Read how we load and deliver sheets.

Abhishek Ranjan
Diploma Civil Engineer, Tashya Ventures

Answers cement, steel and building questions at our Reva Road store, Muzaffarpur. The figures on this page come from the makers' own sheets and from IS 3007 Part 1, checked on 12 Nov 2026. Where the makers disagree, the page says so and uses the safer figure. Send a photo of your frame on WhatsApp before the sheets go up and we will look at it with you.

Where the numbers come from

  1. BirlaNu (Charminar), Fiber Cement Roofs page: lengths 1–4.25 m, width 1050 mm, 6 mm, 12.3–12.7 kg per metre, wave pitch 146 mm and depth 48 mm, IS 459:1992, 91% effective cover on 3 m. No asbestos statement, no purlin figures.
  2. Everest Industries, CBS fibre cement roofing page: 3.6 m in the length list, width 1.05 m, cover 1.01 m, 91% cover and 2.88 m² per 3 m sheet, purlins at most 1.4 m, overhang at most 0.3 m, end lap 150 mm, side lap 44 mm (caption says 40 mm), "Asbestos Fibre Cement" in the picture caption. No weight.
  3. Everest Industries, Hi-Tech brochure (file dated 22 Sep 2022): 13.00 kg per running metre, lengths 1.0 to 3.0 m, side lap 50 mm, end lap 150 mm, purlins at most 1400 mm, overhang 300 mm, minimum slope 10 degrees, non-asbestos PVA fibre. Everest's Hi-Tech web page gives 12.44 kg per metre.
  4. Everest Industries, Roof sheet installation guide: cut on the ground, start from the side away from the wind, walk boards. Written for sheets in general.
  5. Bureau of Indian Standards, IS 3007 (Part 1):1999, laying of corrugated asbestos cement sheets: purlin spacing 1.4 m for 6 mm roofing sheets, eave overhang 300 mm, end lap at least 150 mm, ridge purlin 75–115 mm from the apex, stack height 1 m on level ground with timber packing, holes drilled and not punched, 2 mm larger than the bolt, through the crown and 75 mm from the edge, roof boards at least 375 mm wide, J- and L-bolts with GI and bitumen washers. Its rules are applied here to all 6 mm cement sheets.
  6. BRANZ (New Zealand), Mind your wall claddings: fibre-cement sheets are carried on edge.
  7. Online per-metre listings that we checked for how sellers quote: IndiaMART (Om Asbestos Traders) and TradeIndia. Both price per metre, neither gives a weight.

Worked out by us from the figures above: 44–46 kg per sheet (12.3–12.7 × 3.6), 3.48 m² laid cover with an end lap (1.01 × 3.45) and 3.64 m² without, the 3.2 m between purlins and the 1.07 m gaps. The 0.2 m eave drip in the calculator is usual practice.

Send us your roof measurements

Slope length, roof length, and your site. We reply on WhatsApp with the number of sheets, the purlins to add, and today's price with the delivery amount.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com