हिंदी Call90310 74624
Home›Guides›Paint
Painting guide · repaint

Repainting old walls: what to scrape, what to do with old distemper, and how much paint

The short answer
  1. Damp checked and fixed
  2. Scrape loose paint and all distemper
  3. Fill cracks
  4. Spot putty
  5. Primer × 1
  6. Paint × 2

A new coat holds only as well as the old layer under it. So the money in a repaint goes on preparation, not on a costlier paint. Going from a dark colour to a light one? Plan a third coat.

1 coat
Primer, even on a repaintBirla Opus asks for it on repainting surfaces too, thinned 1:1.
2–3
Coats of paintTwo for the same shade. Three from dark to light: about half as much paint again.
0
Distemper left under emulsionEmulsion grips the chalk, not the wall, and peels with it.
The same wall, before and after
Cross-section of an old wall before and after a proper repaint Before: on the plaster there is a patch of old chalky distemper, a stretch of firm old paint, a crack, and a flake of paint lifting off with white salt under it. After: the distemper is scraped off and puttied, the firm old paint is kept, the crack is filled, the flake area is scraped and puttied, then one coat of primer and two coats of new paint run across the whole wall. BEFORE what the scraper finds distemperold, chalky old paintfirm crack flakesalt under scrape off keep, sand open, fill stop damp room side ↑ old coat plaster brick AFTER what you build scraped,puttied old paintkept crackfilled scraped,puttied Paint × 2 Primer × 1 fixed base plaster brick 1 2 3 4 5 scrapefillspot puttyprimerpaint × 2
Not to scale. Blue-grey is the old colour; it stays only where it was firm. Primer and both new coats run over the whole wall, patched and unpatched.
Before you buy a single tin

Four checks that tell you what your wall needs

Ten minutes with a coin, a damp cloth, cello tape and a plastic sheet. What you find decides the list: the same room can need 2 kg of putty or 23 kg.

OVERNIGHT drops under = water in wall

1 · Damp and salt

Look low, near the floor and behind bathrooms

Dark patches, a tide mark, bubbles or white powder mean water is moving through the wall. Tape a plastic sheet on the spot overnight (usual practice): drops under it in the morning means the wall is wet.

Found it? Stop the water before anything else. Painting a seelan wall
firm hollow ₹ DHAB

2 · Tap test

Tap the wall all over with a coin

A sharp "tok" is paint stuck to plaster. A dull "dhab" is paint, or plaster, that has come loose underneath. Mark every hollow patch with a pencil.

Hollow? Scrape the paint back to a firm edge. Hollow plaster needs a mason first.
white on the cloth = chalky coat

3 · Cloth test

Rub hard with a damp cloth

If colour or white powder comes off on the cloth, the old coat is distemper or chalky paint. Nothing sticks to it for long.

Colour on the cloth? All of it has to come off. How to scrape distemper
paint on the tape = old paint not holding

4 · Tape test

Press cello tape hard, rip it off fast

Do it in three or four places, including near windows and the floor (usual practice). Clean tape means the old paint is holding well enough to paint over.

Paint on the tape? That area gets scraped. Large areas: treat it as a full new-wall job.
The repaint path

Seven steps, in this order

Every figure is from the Birla Opus or Birla White sheet for the product. Where the two disagree, we give the safer one and say so.

StepWhat the sheet says
1 · Fix damp firstNo paint, putty or primer cures a leakdry wallOpus: rectify the source of seepage before painting inside. Let the wall dry fully: test by touch and colour, usually a few weeks after the leak is fixed.
2 · Clean and scrapeLoose, hollow, flaking, chalky: offto a firm edgeOpus: remove loose paint, dust and grease; wire-brush fungus and algae. Distemper under emulsion: all of it.
3 · Open and fill cracksWiden a hairline slightly so filler can enter≤ 3 mm: Crack MasterWider: 1 cement : 4 river sand. Cracks that keep growing: check if structural. Opus sheets give 3 mm and 5 mm; we use 3.
4 · Holes and dentsNail holes, chipped corners1 : 3Opus: cement putty, or white cement with fine sand 1:3.
5 · Spot putty, then sandFull putty only on a scraped or rough wall≤ 1.5 mmBirla White: both putty coats together no thicker than 1.5 mm. Sand firm old paint lightly too, so the new coat can grip; wipe off all dust.
6 · Primer, one coatOver the whole wall, not just the patches1 L + 1 L waterOpus: "for both freshly plastered or repainting surface". Dry at least 4 h.
7 · Paint, two coatsThree from dark to light4–6 h apartOpus: 1 L paint + 500–600 ml water, 2–3 coats "to ensure good hiding". Not above 90% humidity.
Salt or chalk left after scraping? Brush white salt off dry; never wash it in. If the scraped plaster still leaves powder on your finger, give it one coat of AllDry Salt Seal before putty. Its sheet wants the wall dry: a moisture-meter reading below 10, if your painter carries one.
Same paint, same batch, one wall. Tinted paint from two different batches can differ slightly. Get the whole room tinted at once, and finish a wall from corner to corner in one go.
The outside walls too? Same order, but wash off dust and algae, use an exterior primer and exterior paint, and expect 2–3 coats. The paint calculator has an "Outside, repaint" setting. A wall that soaks up rain needs outside-wall waterproofing first.
The most common repaint failure

Old distemper: scrape all of it before emulsion

Many older houses in Muzaffarpur have distemper under the last coat. It is the cheapest finish: chalk held by very little binder. Emulsion is a tougher film, and it needs something solid to grip.

Why emulsion peels off old distemper Left: emulsion on top of loose chalky distemper grains. As the emulsion dries it pulls, and it lifts off carrying grains of chalk on its underside. Right: emulsion on primer on scraped plaster stays flat and gripped. ON DISTEMPER ON SCRAPED PLASTER grips the chalk, peels with it often within a monsoon paint × 2primer grips the plaster, stays primer binds the surface pulls as it dries
Asian Paints lists emulsion over distemper as a cause of blistering and peeling.

1How to get it off

  1. Wet a section of wall with plain water and wait 10–15 minutes so the distemper softens (usual practice).
  2. Scrape with a broad scraper until you reach hard plaster. Wire-brush the corners.
  3. Run a finger over it. Still powdery? Brush, then one coat of AllDry Salt Seal.
  4. Let it dry, then full putty: a scraped wall is too uneven for spot putty. Putty or no putty

2Where the makers differ

Birla Opus's own article says the distemper layer should be sanded and primed before emulsion. Asian Paints says remove it completely. We go with removal: a primer can only soak a little way into old chalk, and a peeled wall costs you the whole job again.

3Staying with distemper?

Distemper over old distemper is fine after brushing off the loose powder (usual practice); it is the cheapest way to freshen a store room or a rented portion. It still won't wash, and lasts 2–3 years. Compare the two: emulsion vs distemper.

Why the litres change

Same shade, new colour, dark to light

Paint does two jobs: it gives a sound film, and it hides what is under it. In the same shade there is nothing to hide, so two coats finish the job. A light colour over a dark one has to hide the old colour, and that takes another coat.

How the wall looks after each coat Three columns, each showing the wall after coat 1, coat 2 and coat 3. Same shade: even after coat 2, no third coat needed. Dark blue-grey to light yellow: muddy after coat 1, faint shadows after coat 2, even after coat 3. A bare patch with no primer: shows as a dull square after coat 1 and still after coat 2; prime the patch first. Same shade Dark to light Patch, no primer old: same yellowold: blue-greyold + bare patch not needed a 3rd coat won't fix it COAT 1COAT 1COAT 1COAT 2COAT 2COAT 2COAT 3 2 coats3 coatsprime first the base figureabout 1.5 × the paintpatch drinks paint
Drawn to show the effect, not an exact colour match. Birla Opus prints 2–3 coats for its emulsions "to ensure good hiding".
Your wallFor a 12 × 10 ft room
Sound, same shade or darkerPrimer × 1, spot putty, paint × 22.8–3.2 Lpaint: one 4 L tin · primer 1.9–2.3 L · putty about 2–3 kg
Sound, light to a different lightSame as above; buy for the high figure2.8–3.2 La strong new shade may still want a third coat on one wall
Sound, dark to lightPrimer × 1, spot putty, paint × 34.1–4.8 Lpaint: 4 L + 1 L · primer and putty as above
Distemper scraped, or peeling and roughPrimer × 2, full putty, paint × 22.8–3.2 Lpaint the same, but primer 4.7–5.8 L and putty 19–23 kg

Room: 12 × 10 ft, 10 ft high, one door, two windows = 387 sq ft of wall, ceiling not included. Paint: Style Color Smart, 120–140 sq ft per litre for two coats (Birla Opus). Primer: ActivCoat Interior, 170–200 sq ft per litre on putty and sound old paint, 110–140 on bare plaster (Birla White). Putty: WallCare, 17–20 sq ft per kg (Birla White); spot putty counted as about a tenth of the wall (usual practice).

How much for your room

Paint, primer and putty for a repaint

Put in the room and answer two questions about the wall. You get a low and a high figure from the makers' coverage, and the tins to buy for the high one.

Not sure? Do the four checks. Colour on the cloth or paint on the tape over big areas means the second option.

Area to paint: — sq ft (door 3×7 ft, window 4×4 ft taken off)

Your repaint list

Style Color Smart, 2 coats—120–140 sq ft per litre for 2 coats (Birla Opus)—
ActivCoat Interior primer, 1 coat—170–200 sq ft per litre per coat on sound old paint (Birla White). Litres from the can, before water.—
WallCare putty, spots only—About a tenth of the wall (usual practice); 17–20 sq ft per kg (Birla White)—
Material totalAsk rate
Send this list on WhatsApp

Tins are for the high figure. Prices are filled in from today's paint rates. Damp to fix first? Salt Seal, crack filler or waterproof putty are not in this list: tell us on WhatsApp and we add them.

Using the full paint calculator for the whole house

On the paint calculator, choose Repaint in step 2. It then counts one primer coat and spot putty on about a tenth of the wall. If old paint is peeling, distemper was scraped, or the wall is rough, tick "putty the whole wall again", and it counts the full new-wall system. The paint litres do not change with this setting: they are for two coats either way. Going dark to light, add half again to the paint line, as this page's calculator does. A whole-house job of 2,000 sq ft or more can qualify for Birla Opus's 1-year free repaint, if it is registered before painting starts.

Agree this before work starts

What to tell the painter

Most repaint quotes are cheap because they skip scraping and primer. Agree the steps first, then compare rates for the same work.

The repaint brief

  • Fix the damp before any work, and wait until the wall is dry.Not "we'll put waterproof putty on it".
  • Scrape every loose, hollow or chalky patch to a firm edge.Tap test and tape test the whole wall, not just the flakes you can see.
  • Remove all old distemper before emulsion.Then full putty on those walls.
  • Open and fill cracks; fill holes with putty or white cement and fine sand 1:3.
  • Spot putty, sand, and wipe off all dust.
  • One full coat of primer, 1 litre primer to 1 litre water.Over the whole wall, not only the patches.
  • Two coats of paint, 4–6 hours apart. Three coats from dark to light.No more than 500–600 ml of water per litre of paint.
  • One tinting batch for the room; cover the floor and furniture.
Send this brief to your painter

Five ways a repaint fails

Paint over seelan or salt

Blisters and white powder come back in a season. Paint peeling: the causes

Emulsion on distemper

Peels off in sheets, carrying the chalk with it.

Primer only on the patches

Patches show through as dull or lighter squares, whatever the number of coats.

Too much water in the paint

It spreads further but hides less, so you end up buying the coat you tried to save.

Dark to light in two coats

The old colour shadows through, most in evening light. Plan the third coat from the start.

Questions people ask us

Short answers

How much paint do I need to repaint a room?

A 12 × 10 ft room with 10 ft walls, one door and two windows has about 387 sq ft of wall. In the same shade or a darker one, two coats of Style Color Smart take about 2.8–3.2 litres: one 4 litre tin. Add about 2 litres of primer for the one coat. Dark to light takes a third coat, about 4.1–4.8 litres. Your own room: the calculator above.

Can I paint emulsion over old distemper? (purane distemper par paint)

Not safely. Distemper is soft and chalky, and emulsion grips the chalk, not the wall, so it peels or blisters with it. Asian Paints says remove distemper completely; Birla Opus says sand and prime it. We follow the safer one: scrape it all off, putty, prime, then paint.

Do I need primer when repainting the same colour?

Yes, one coat. The Birla Opus Style Color Smart sheet asks for one coat of primer, thinned 1 litre to 1 litre of water, "for both freshly plastered or repainting surface". It costs about 2 litres for a 12 × 10 ft room, and it stops the patches showing through.

How many coats for repainting a dark wall in a light colour?

One coat of primer and three coats of paint. Birla Opus prints 2–3 coats "to ensure good hiding", and dark to light is where the third one is needed. Plan about half as much paint again as a same-shade repaint.

Can the same shade be done in one coat?

Some painters offer it. The makers' sheets ask for at least two coats; with one, every scraped or puttied spot shows as a different-looking patch, and the film is thin where the wall gets touched most.

Do I have to remove all the old paint?

No. Only what is loose, hollow, flaking, chalky, or distemper under emulsion. Firm old paint stays: sand it lightly for grip and wipe off the dust. Asian Paints lists not sanding an old glossy coat as a cause of poor grip.

What if white powder keeps coming on the wall?

That is salt carried out by water moving through the wall. Paint over it lasts a season at most. Find and stop the water, let the wall dry fully, brush the salt off dry, then one coat of AllDry Salt Seal before the repaint. Start here: painting a seelan wall.

Does a repaint need full putty again?

Not on a sound wall that was puttied before: spot putty on the dents is enough. A wall where distemper was scraped, or one with many dents or peeling, needs full putty again. Putty or no putty walks you through it.

Mr Mustafaa
Paint Engineer, Tashya Ventures

Paint Engineer at our Reva Road store, Muzaffarpur. Every number on this page was checked against the maker's own product sheet on 12 Nov 2026. Where the makers disagree, the page says so and gives the safer figure.

Where the numbers come from

  1. Birla Opus, Style Color Smart product information sheet (CS0002/05/2024): remove loose paint, dust and grease; chalky surface: water, then AllDry Salt Seal; fix interior seepage first; cracks up to 5 mm wide and 3 mm deep with AllDry Crack Master, larger with 1:4 cement and river sand; holes with cement putty or white cement and fine sand 1:3; one coat of primer 1:1 "for both freshly plastered or repainting surface", 4 h; paint 1 L + 500–600 ml water, 2–3 coats "to ensure good hiding", 4–6 h; 120–140 sq ft/L for 2 coats; coverage varies with surface condition; not above 90% humidity.
  2. Birla Opus, AllDry Salt Seal information sheet (SS002/08/2024): one coat, 1 L + 1 L water; moisture meter below 10; chalky surface: water, then Salt Seal; cracks up to 3 mm with Crack Master (the figure we use); stop seepage first.
  3. Birla Opus, Calista Ever Wash Shine information sheet: 130–150 sq ft/L for 2 coats. One Pure Elegance: 140–160 sq ft/L for 2 coats, from its Birla Opus sheet, as used on our paint calculator.
  4. Birla Opus, Emulsion vs distemper: which is better: distemper should be sanded and primed before emulsion; distemper lasts 2–3 years.
  5. Asian Paints, Paint defects FAQs: emulsion over distemper causes blistering; remove distemper completely before emulsion; remove peeling paint to a firm edge; not sanding an old gloss coat causes adhesion failure; salts in a damp wall cause efflorescence.
  6. Birla White, ActivCoat Interior primer page: 1:1 by volume, 170–200 sq ft/L per coat on putty, 110–140 on plaster.
  7. Birla White, Wall putty work: step-by-step process: both coats together 1.5 mm at most, 17–20 sq ft/kg.
  8. Birla Opus, Opus Assurance: 1-year free repaint for jobs of 2,000 sq ft or more, registered before painting starts, with Opus products and an Opus-registered contractor.
  9. Usual practice, marked as such on the page: the plastic-sheet, coin and tape tests, wetting distemper before scraping, spot putty at about a tenth of the wall, distemper over old distemper.

Send us a photo of the wall

With the room size. We'll tell you what to scrape and send back the list, with today's price, on WhatsApp.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com