हिंदी Call90310 74624
Home›Problems›Paint
Problem and fix · walls

Paint peeling off the wall: the five causes, and the fix for each before you repaint

The short answer

Paint rarely peels because the paint is bad. It peels because something under it stops it gripping: water, wet plaster, old distemper, too much water in the tin, or salt. New paint over the flakes peels again, usually within one season. Fix it in this order:

  1. Stop the water
  2. Let it dry
  3. Scrape to a firm edge
  4. Right first coat
  5. Paint × 2
28 days
New plaster, before paintWater it daily, then let it dry. Birla Opus sheets.
< 10
Moisture meter readingDry enough to paint. Higher means fix the water first.
1 : 1
Salt Seal and waterOne coat on salty or chalky patches, before anything else.
What lifts the paint off a wall
Cross-section of a peeling wall with five causes marked From the brick outwards: brick, cement plaster, an old chalky coat, then paint. Five weak points are marked: paint thinned too much at the top, paint gripping old distemper chalk, wet plaster, water coming through the brick from behind, and salt crystals growing under a blister. BRICKPLASTERPAINT ROOM 4 3 2 1 5 Too much water Old distemper,no primer Wet plaster Damp behind Salt weak, thin film grips chalk, not wall painted too soon water pushes fromthe brick side crystals grow underthe paint
Not to scale. Numbers match the five causes below. Causes 1 and 5 usually come together: the water carries the salt.
Read the wall first

Where it peels, and when it started, tells you why

Look at the whole wall before you look at the flake. Most walls we see in Muzaffarpur fit one of these.

A room wall with the usual places paint peels A room wall under a roof slab, with a window. Marked: a stain under the roof corner and a patch around a pipe from the bathroom behind (damp, cause 1); a large sheet of paint peeling in one piece (old distemper, cause 3); bubbles under the window in a new house (wet plaster, cause 2); thin streaky paint (too much water, cause 4); a tide mark and white powder along the bottom 2 to 3 feet (rising damp, cause 1, and salt, cause 5). bathroom pipe behind the wall 2–3 ft 1 1 1 3 2 4 5

1Damp behind the wall

A patch under the roof or parapet, around a pipe or below a bathroom, or a wavy brown line along the bottom 2–3 ft. The wall feels cool.

Starts or grows after the rains.

2Wet, uncured plaster

Bubbles and peeling all over a new house, with dark and light patches in the wall.

Within months of a new house being painted.

3Old distemper or no primer

Paint comes off in big sheets, and the back of each sheet is white and chalky.

Months after a repaint over old paint.

4Too much water in the paint

Dull, streaky paint, putty showing through, colour that rubs off on a wet palm.

Soon after painting; outside walls wash out in the first monsoon.

5Salt

White powder or fluffy crystals under the flakes or on the wall, often along with cause 1.

Comes back days after you brush it off.

?Not sure?

Two causes often sit together. Send three photos (how to take them) and we'll tell you which it looks like.

The five causes

How to tell each one, what to scrape, what to put on

Each picture shows the layers on the left (the red one is the trouble) and the wall on the right. Products link to their page on our site.

WATER BEHIND

1Damp behind the wall (seelan)

You see: blisters, a brown stain, a tide mark
How to tell
Press the back of your hand on the bare patch: cool or damp means water. The patch grows after rain. Near the floor it stops at a wavy line 2–3 ft up.
Scrape
Every blister and loose flake, back to paint that won't lift with a blade. Soft, crumbly putty comes off too.
Then apply
Fix the waterDry: weeksSalt SealWaterproof puttyPrimerPaint × 2
Which fix for which water is in the repair order. Outside walls that soak in rain: AllDry WallFix 4 in place of the putty.
Photo enough? Only for the paint. The leak itself needs a plumber or mason first.
< 28 DAYS

2Painted on wet or uncured plaster

You see: bubbles, dark patches, peeling in a new house
How to tell
Paint went on less than 28 days after plastering, often rushed for griha pravesh. The bare wall under a flake looks darker in patches.
Scrape
All lifting and bubbled paint. Then leave the bare wall open to dry. Fresh plaster is also strongly alkaline, which attacks paint.
Then apply
Salt Seal is an alkali-block primer, made for this. Its sheet still asks for a wall that reads below 10 on a moisture meter.
Photo enough? Yes, with the date the plaster was done.
CHALK UNDER

3Emulsion over old distemper, or no primer

You see: paint coming off in big sheets
How to tell
Rub the old wall with a wet palm. White chalk on your hand means distemper or a powdery coat. The back of a peeled sheet is white and dusty.
Scrape
All the distemper, not only the part that is falling. Wet a patch, scrape, wash, let dry. Asian Paints' paint-defects page says remove distemper completely before emulsion; we follow that.
Then apply
The Opus sheet: on a chalky surface, water it, then put Salt Seal before anything else. Order of work: repainting old walls.
Photo enough? Yes. Add a photo of your palm after the wet rub.
TOO THIN

4Too much water in the paint

You see: thin, dull, streaky paint that scratches off
How to tell
A fingernail scratches it off easily. A wet palm comes away coloured. White putty shows through. Ask how much water the painter added per litre.
Scrape
Sand or scrape the weak coat until nothing comes off on a wet palm. Wipe off the dust.
Then apply
Style Color Smart takes 500–600 ml of water per litre at most; every Opus sheet says don't over-dilute. Measure with a mug: the right water for each tin.
Photo enough? Yes. Need more cover? Add a coat, not water.
SALT

5Salt coming out of the wall

You see: white powder or crystals, paint pushed off
How to tell
White powder under or on the flakes, mostly low on the wall or near a leak. Brush it off dry; if it is back in a few days, water is still moving through.
Scrape
All loose paint. Brush the salt off with a dry stiff brush. Don't wash it in: water carries more salt out.
Then apply
Stop the waterSalt Seal, 1 coatWaterproof puttyPrimerPaint × 2
Salt Seal: 1 L with 1 L water, one coat, 4–6 hours to dry. Opus makes it for mild salt. Heavy, coming-back salt is a water problem: white salt on walls.
Photo enough? Yes. Send one now and one a week after brushing.

What does not cause peeling

The brand. We sell only Birla Opus, and the same tin that peels on one wall lasts years on the next. Asian Paints' own defects page puts peeling down to dirt or the wrong layer underneath, not the paint.

A thicker coat of new paint won't hold old paint on either. If the coat under it is loose, everything comes off together.

Send us a photo

The repair, in order

Fix it once: water, dry, scrape, first coat, paint

Skip a step and you paint the same wall again next year. The numbers in red say which cause needs the step.

  1. Stop the waterFind where it comes in and fix it with the right product (table). No paint, putty or primer cures a leak; the Opus sheets say fix the source of seepage first.CAUSES 1 · 5
  2. Let the wall dry fullyTest by touch and colour: the patch should feel as warm as the rest of the wall and be one even colour. Usually a few weeks after the leak is fixed. With a moisture meter, the Salt Seal sheet asks for below 10. New plaster: 28 days of curing first.CAUSES 1 · 2 · 5
  3. Scrape back to a firm edgeRun a blade under the edge of the good paint. If it lifts, keep going. Take off all old distemper.ALL
  4. Brush and wipe cleanDry brush for salt, sandpaper and a cloth for dust. Primer sticks to dust, not to the wall.ALL
  5. Fill cracksHairline to 3 mm: Birla Opus AllDry Crack Master (we can order it). Wider: cement and sand mortar, or a mason. A crack that keeps opening: cracks before painting.WHERE CRACKED
  6. The right first coatSalt Seal on salt, chalk or fresh plaster. WallFix 4 on outside walls that soak in rain. Plain primer if the wall was only loose. See the second table.ALL
  7. Putty, primer, two coats of paintInside: putty only on the scraped patches, sanded flush, then primer and paint as in putty, primer, paint. Outside: 2–3 coats of exterior paint.ALL
Step 1: where the water comes from
SourceFix first
From the groundbottom 2–3 ft, tide markSeep Blocker 2K, then Waterproof putty · plinth damp
Roof or parapetceiling, top cornersWeather Pro Hi-Flex coating, WP+200 in repair mortar · roof leaks
Bathroom behindpatch around a pipeSeal & Dry SBR in the base coat, Hi-Flex under the tiles · bathroom
Outside wall in rainwet after every showerWP+200 in the plaster, then AllDry WallFix 4 and Opus exterior paint

The whole story of damp in a Bihar house: seelan from foundation to roof. Painting a wall that has been damp: damp wall painting.

Step 6: which first coat
Your wallThen
Inside, salt, chalk or fresh plasterSalt Seal (1:1, one coat) → putty on patches → ActivCoat primer → paint × 2Salt Seal sheet, interior walls
Inside, only loose paintPutty on patches → ActivCoat primer → paint × 2
Outside, saltSalt Seal → exterior paint × 2–3Salt Seal sheet, exterior walls
Outside, parapet, chhajja, soaks in rainWallFix 4: first coat with 10% water, second coat neat → exterior paint × 2–3WallFix 4 sheet
Outside, only loose paintStyle Perfect Start primer → Style Power Bright × 2
WallFix 4 is not for inside rooms. Its sheet says it is for outside vertical walls, parapets and chhajjas, under Opus exterior paint, and never on a wet or visibly damp wall, or above 80% humidity. Opus's own web page also mentions bathrooms and kitchens; we follow the sheet. For an inside wall that has been damp, the fix is the water plus Salt Seal and Waterproof putty.
Cause 4, prevented

How much water goes in each tin

Painters thin by eye. Use a measuring mug instead. These are the makers' own figures, per litre from the tin.

Water to add per litre for five products Five measuring jugs, each with one litre of product at the bottom and water above it: Style Color Smart paint, 500 to 600 millilitres; interior primer, 1 litre; Salt Seal, 1 litre; WallFix 4 first coat, 100 millilitres; WallFix 4 second coat, no water. +1 L +2 L 500–600ml water 1 Lwater 1 Lwater 100 mlwater noneneat Style ColorSmart paint Interiorprimer Salt Seal1 coat WallFix 4coat 1 WallFix 4coat 2 2–3 coatsboth coats80–100 sq ft/Loutside walls only Bottom part of each jug = 1 litre from the tin
From the Birla Opus sheets for Style Color Smart, Salt Seal and WallFix 4; interior primer 1:1 from the Style Color Smart sheet and Birla White ActivCoat.
ProductWater per litre
Style Color Smartinside paint, Opus sheet: "do not over dilute"500–600 ml
ActivCoat Interior primerboth primer coats, inside1 L
AllDry Salt Sealone coat; "do not excessively thin"1 L
AllDry WallFix 4, coat 1outside walls; repaint needs only coat 2100 ml
AllDry WallFix 4, coat 2none
Thinned paint doesn't keep. The Salt Seal sheet says use thinned material within 24 hours, and thin only what you will use that day. Don't use chlorinated water to dilute.
WhatsApp diagnosis

When a photo is enough, and when it isn't

Send three photos to 90310 74624. We look at them with you, tell you which cause it looks like, and send the list with today's price.

A photo is enough when

  • The wall is dry now, and the paint peels in sheets or flakes (causes 3 and 4).
  • A wet palm comes away white or coloured.
  • A new house was painted soon after plastering (cause 2). Tell us the plaster date.
  • White powder sits on a wall that is no longer getting wet.

Fix the water before any paint when

  • The patch is cool, wet or growing, or gets worse after every rain.
  • The tide mark near the floor is climbing.
  • The ceiling peels under the roof: roof leak.
  • A crack is wider than 3 mm, or the plaster sounds hollow when tapped: a mason looks first.
The three photos to send: the whole wall, a close-up with a coin, and the back of a flake on your palm 1 ₹ 2 3
  1. Whole wallfrom the doorway, floor and ceiling in the frame
  2. Close-upwith a coin beside the peel, for size
  3. Back of a flakeon your palm, in daylight

Send photos on WhatsApp

How much to buy

Material for the patch you are repairing

Put in the size of the scraped area and what the wall needs. Quantities use the makers' coverage figures; buy for the high number.

Area: — sq ft

Your list

Material totalAsk rate
Send this list on WhatsApp

Putty for the patches and Crack Master are not in the list: tell us on WhatsApp and we add them. Prices are filled in from today's rate. Whole rooms: paint calculator.

Questions people ask us

Short answers

Can I paint over peeling paint?

No. The new coat sticks to the loose old coat and comes off with it. Scrape back to a firm edge first. Asian Paints' paint-defects page says the same: remove all soft coating back to a firm edge, or remove it all.

Why does paint peel in the rains? (barsat mein paint kyun ukhadta hai)

Rain gets into the wall through the roof, parapet, chhajja or an outside wall, and the water pushes the paint off from behind. Fix where the water gets in, let the wall dry fully, and only then repaint. Painting in the wet season: painting in the monsoon.

What is the white powder under the peeling paint?

Salt (efflorescence, shora). Water carries salts out of the brick, sand and ground water; the water dries and the salt is left behind, under the paint. Stop the water, brush the salt off dry, then put one coat of AllDry Salt Seal before repainting.

How long after plastering can I paint?

Birla Opus asks for 28 days of daily water curing on new plaster, and then a dry wall. Its Salt Seal sheet asks for a moisture meter reading below 10 before painting.

Will waterproof paint inside the room stop the peeling?

Not while water is still coming through. The Birla Opus sheets say to find and fix the source of seepage first. A coating on the inside face only holds the water in for a while.

Can Salt Seal stop seelan?

No. It is a primer that blocks salt and alkali coming through to the paint, and Opus describes it for mild salt. Its own sheet says: if a wall has seepage or dampness, find and stop the source, let it dry, then apply.

Does the paint warranty cover peeling?

Birla Opus warranties cover manufacturing defects in the affected area only, need registration within 15 days of purchase, and need the recommended system and coverage to have been followed. Peeling from damp or poor preparation is not a manufacturing defect. That is one more reason to fix the wall first.

Mr Mustafaa
Paint Engineer, Tashya Ventures

Paint Engineer at our Reva Road store, Muzaffarpur. Every number on this page was checked against the maker's own product sheet on 12 Nov 2026. Where the makers disagree, the page says so and gives the safer figure.

Where the numbers come from

  1. Birla Opus, AllDry Salt Seal information sheet (SS002/08/2024): alkali-block primer, 1 L + 1 L water, one coat, 4–6 h, 1/4/20 L, interior and exterior systems, moisture meter below 10, wall pH below 10, cracks up to 3 mm with Crack Master, chalky surface: water then Salt Seal, seepage: stop the source first, use thinned material within 24 h. The sheet gives coverage both as 100–120 and as 80–100 sq ft/L; we use 80–100.
  2. Birla Opus, AllDry Wall Fix 4 information sheet (WF12002/2024): waterproofing basecoat for outside vertical walls, parapets and sunshades under Opus exterior paint; coat 1 with 10% water, coat 2 neat; 40–45 sq ft/L; 4–6 h; 1/4/10/20 L; not on wet or visibly damp walls or above 80% humidity; no rain within 48 h. It allows Crack Master up to 5 mm; the Salt Seal sheet says 3 mm, so we give 3 mm.
  3. Birla Opus, Style Color Smart product information sheet (CS0002/05/2024): 28-day plaster cure, remove loose paint, chalky surface: water then Salt Seal, interior seepage: fix the source first, primer 1:1, paint 1 L + 500–600 ml water, do not over-dilute, 120–140 sq ft/L.
  4. Birla Opus, AllDry Wall Fix 4 web page (FAQ mentions interior use) and warranty terms: manufacturing defects only, register within 15 days.
  5. Birla Opus, Style Perfect Start and Style Power Bright sheets: 80–100 sq ft/L primer, 50–60 sq ft/L for 2 coats.
  6. Birla White, ActivCoat Interior primer page: 1:1 by volume, 110–140 sq ft/L per coat on plaster, 170–200 on putty.
  7. Asian Paints, Paint defects FAQs: peeling is loss of bond from contamination or incompatible coats; remove soft coating to a firm edge; remove distemper completely before emulsion.

Send us a photo of the peeling

We'll tell you which cause it looks like and send the list for your wall, with today's price, on WhatsApp.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com