हिंदी Call90310 74624
Home›Guides›Wires and electrical
Wiring guide · AC line

Which wire for a 1-ton, 1.5-ton and 2-ton AC? Size, MCB and socket

The short answer
  • ≤ 12 AMost 1-ton and 1.5-ton splits2.5 sq mm wire × 3 (phase, neutral, earth), a 16 A C-curve MCB, a 16 A socket.
  • 12–16 ASome 2-ton and older fixed-speed units4 sq mm wire × 3, a 20 A C-curve MCB, a direct point.

The amps printed on your AC's name plate decide which row you are in, not the tonnage. And every AC gets its own line from the board, with nothing else on it.

18 A
2.5 sq mm in conduitV-Guard Classo+. So the MCB on it is 16 A, never 20 A.
24 A
4 sq mm in conduitV-Guard Classo+. This is the wire that can take a 20 A MCB.
C
Curve of the MCBRides through the compressor's start. A B-curve trips on it.
One AC, one line: what goes in
The wiring for one split AC, from the board to the AC A distribution board with one MCB kept for the AC. Three wires, red phase, black neutral and green earth, run up inside a conduit pipe in the wall and across to a 16 A socket and switch beside the indoor unit. The AC's name plate sits on the side of the unit. SPLIT AC in a pipe in the wall, laid before plaster BOARD 16C10B10B16C20C ACother circuits 1 2 3 4 5 1 2 3 4 5 Its own MCB: 16 A, C-curve 3 wires, 2.5 sq mm, same size In conduit: the wire's limit is 18 A 16 A socket and switch The name plate nothing else connected to it red phase · black neutral · green earth so the MCB is 16 A, not 20 A or a direct point, if the plate is over 12 A its amps decide everything above
Drawn for the common case: a 1 or 1.5-ton split whose plate shows 12 A or less. Above 12 A the same picture holds with 4 sq mm wire, a 20 A C-curve MCB and a direct point. Wire figures: V-Guard Classo+.
Step one

Read the amps on your AC's name plate

Tonnage tells you how much cooling an AC gives. The wire has to carry the current the AC draws, and that changes with the brand, the star rating and whether it is an inverter model. The plate gives the exact figure.

  1. Find the plateIt is a printed sticker or metal plate, usually on the side of the outdoor unit. Many indoor units carry one too, under the front flap. On a window AC it is on the side or the back. If the AC isn't bought yet, the same figures are in the brochure or the manual.
  2. Find the current, in AThe line may say "Rated current", "Running current" or "Operating current". Ignore the kW and BTU lines for this; those are cooling.
  3. Take the bigger numberSome plates also print a "Max. current". If yours does, use that one. It is the figure the line must survive on the hottest afternoon.
  4. Can't read it?Send a photo of the plate on WhatsApp 90310 74624 and we'll read it with you.
Where the name plate is, and which line to read An outdoor unit with a yellow plate on its side, and the plate drawn large. The line for rated current in amps is circled in red. A second line for maximum current is marked: use it if it is printed. outdoor unit, side panel what the plate looks like AIR CONDITIONER Model●●●●● Cooling capacity–.– kW Power supply230 V ~ 50 Hz Power input–––– W Rated current–.– A Max. current–– A Refrigerant–––– Weight–– kg Read this line: current, in A Called "rated", "running" or "operating" current. If a "max. current" line is also printed, use that. 12 A or less 2.5 sq mm · 16 A C MCB · 16 A socket Over 12 A, up to 16 A 4 sq mm · 20 A C MCB · direct point
The plate is drawn without numbers on purpose: read your own. Over 16 A, send us the plate before buying anything.

Why tonnage can't tell you the wire. A "ton" is a measure of cooling: one ton of refrigeration is about 3.5 kW of heat taken out of the room. How much electricity the AC uses to do that depends on its compressor and star rating. Two 1.5-ton ACs from different makers can print quite different amps.

Step two

Match the wire and the MCB to the plate

The MCB's job is to switch off before the wire gets too hot. So the MCB has to be smaller than what the wire can carry, and big enough that the AC runs all night without tripping it.

Wire limit vs MCB, in amps
Which MCB is safe on which wire Three bars. 2.5 sq mm in conduit carries 18 A; a 16 A MCB sits inside that, which is safe. The same wire with a 20 A MCB leaves a gap between 18 and 20 A where the wire overheats and the MCB stays on: not safe. 4 sq mm carries 24 A; a 20 A MCB sits inside it, which is safe. 051015202530 A 2.5 sq mm + 16 A MCB SAFE 18 MCB 16 2.5 sq mm + 20 A MCB NOT SAFE 18 MCB 20 wire overheats, MCB stays on 4 sq mm + 20 A MCB SAFE 24 MCB 20
Dark bar: what V-Guard Classo+ carries in conduit. Red line: the MCB rating. The MCB must sit inside the bar.
Plate currentWire, MCB and connection
≤ 12 A2.5 sq mm × 3 · 16 A C-curve MCB16 A socket with its switch. Most 1-ton and 1.5-ton home splits.
12–16 A4 sq mm × 3 · 20 A C-curve MCBDirect point through a 20 A switch, no socket. Check twice on 2-ton and old fixed-speed units.
Over 16 ASend us the plate firstThis needs a heavier line than a normal house AC point. We'll work it out with your electrician. Rare in homes here.
Any ACNever 1.5 sq mmIt carries 13 A in conduit (Classo+) and is meant for light and fan circuits. See wire amps chart.
Why 12 A on a 16 A MCB, and not 16 A? An AC runs for hours: right through a Muzaffarpur summer night, in a board that gets warm. A common design rule is to load an MCB to about 80% of its rating when the load runs for hours: 80% of 16 A is 12.8 A, of 20 A it is 16 A. We round down. It keeps the MCB from tripping at 2 am on the hottest night, and keeps the wire cool.

What electricians here run. For a 1-ton or 1.5-ton split, most run 2.5 sq mm; some run 4 sq mm for every AC point to be safe for a bigger AC later. Both are right when the plate fits. 2.5 sq mm is the minimum: if your electrician suggests 1.5 sq mm "because it's only 1 ton", say no. If the board-to-AC run is long, use the calculator below: past about 30 m, 4 sq mm is often worth it.

The MCB question

16 A or 20 A? And why it must be C-curve

An AC's compressor is a motor. Every time it starts, it pulls a short burst of current much higher than its running current. The MCB has to tell that harmless burst apart from a real fault.

Compressor start compared with the instant-trip bands of B and C curve 16 A MCBs A line showing current over time: low while running, with a short tall spike each time the compressor starts. For a 16 A MCB, the B-curve instant-trip band is 48 to 80 A and the C-curve band is 80 to 160 A. The spike reaches into the B band, so a B-curve MCB can trip at start; it stays below the C band. 160 A80 A48 A16 A0 MCB rating C-CURVE TRIPS HERE B-CURVE TRIPS HERE 5 to 10 × rating3 to 5 × rating start running time → (each start lasts a moment)
Bands for a 16 A MCB from the V-Guard Elegna data sheet: B trips instantly at 3–5 times its rating, C at 5–10 times. The start spike is drawn to show the idea; its height differs from AC to AC.

1C-curve, not B-curve

A B-curve MCB trips at once when current reaches 3 to 5 times its rating. A starting compressor can get there, so the MCB drops every time the AC kicks in. A C-curve waits until 5 to 10 times its rating. It lets the start through and still trips on a short circuit. B-curve is for lights and fans.

216 A or 20 A: the wire decides

On 2.5 sq mm (18 A in conduit) the MCB is 16 A. On 4 sq mm (24 A in conduit) it is 20 A. A 20 A MCB on 2.5 sq mm is the most common mistake we see: between 18 and 20 A the wire runs hot inside the wall and nothing trips.

3Tripping often? Don't go bigger

If a correct 16 A C-curve keeps tripping, something is wrong: a shared line, a loose joint, or an AC drawing more than its plate. Swapping in a 20 A only hides it. See MCB tripping again and again.

V-Guard Elegna is 10 kA, single pole from 6 to 63 A, B and C curve, IS/IEC 60898-1. We keep the 20 A C-curve and 10 A B-curve on the shelf. The 16 A C-curve for a 2.5 sq mm AC line is ordered for you: ask on WhatsApp for the time it takes. Elegna MCB · B vs C curve

At both ends of the wire

A 16 A socket or a direct point, and a line of its own

Socket or direct point

On a 2.5 sq mm line with a 16 A MCB: a 16 A socket with its own switch, next to where the indoor unit will hang. You can switch it off and pull the plug when the AC is serviced. Our Torio 6/16 A socket takes the AC's big plug, and the 16 AX switch goes beside it.

On a 4 sq mm line with a 20 A MCB: a direct point, where the wire goes through a 20 A switch straight to the AC's lead, with no plug. A 16 A socket shouldn't sit on a 20 A circuit, because the MCB would let the socket run past its own rating.

Never a 6 A socket, and never a 3-pin adapter. Their contacts are made for a TV or a charger. On an AC they heat up and scorch, usually in the first summer. More in 6 A vs 16 A switch and socket.

Its own line from the board

One MCB, one AC, one run of wire. Don't take the AC from the room's light and fan circuit, the room's sockets, the geyser line or another AC's line. Two ACs means two lines and two MCBs. Building new? Mark the AC points before the walls are chased, so the conduit goes in then: AC point before plaster.

The earth wire is not optional

The green earth wire is the same size as the other two: 2.5 sq mm on a 2.5 line, 4 sq mm on a 4 line. The standard wiring rule keeps earth the same size as the phase wire up to 16 sq mm. The AC's metal body and outdoor unit sit on it. It only helps if the house earthing is sound: earthing basics.

If your house has a mainline stabiliser

A V-Guard VGMW 500 Plus is rated 15 A for the whole house. Lights, fans, TV and fridge fit; an AC on top of them can push the total past 15 A. Take the AC line from the board before the stabiliser. Most inverter ACs list a wide working voltage in their manual. Read it before buying a separate one: stabiliser for an inverter AC.

Own line vs shared line
An AC on its own line compared with an AC on a shared line Top: right way. The board has a separate 16 A C MCB with one run of wire to the AC only. Bottom: wrong way. The AC is joined onto the room's 10 A light and fan circuit with 1.5 sq mm wire, together with a bulb and a fan; the MCB trips and the joint heats up. ✓ RIGHT 16C 10B board AC AC alone on its MCB2.5 sq mm, nothing elselights, fans ✗ WRONG 10B tripped board AC AC joined to thelight-fan circuit1.5 sq mm, 10 A B MCB:trips, joint heats uphot joint
Lights and fans usually sit on 1.5 sq mm with a 10 A B-curve MCB. That circuit was never meant to carry an AC.
What goes wrong

Six AC wiring mistakes, and how they show up

Most of these are hidden in the wall. You find out in May, when the AC runs all night for the first time.

20AON 2.5 SQ MM · 18 A LIMIT inside the wall, out of sight

20 A MCB on 2.5 sq mm

You see: nothing, until the insulation goes

2.5 sq mm carries 18 A in conduit. With a 20 A MCB, the wire can run hot for hours without a trip. Use 16 A on 2.5, or move up to 4 sq mm for 20 A.

10B AC SHARED 1.5 SQ MM LINE

AC taken from the room's light circuit

You see: the room goes dark when the AC starts

A light-fan circuit is thin wire behind a small B-curve MCB. The AC trips it, or worse, someone fits a bigger MCB on it. Run a new line from the board.

6 A brownscorch loose,hot pins

6 A socket or an adapter

You see: a brown, melted socket and a hot plug

Small sockets and adapters aren't made for an AC's current. Use a 16 A socket on a 16 A line, or a direct point on a 20 A line.

B TRIPTRIPTRIP each compressor start

B-curve MCB on the AC line

You see: the MCB drops when the AC switches on

B-curve trips instantly at 3 to 5 times its rating, which a compressor start can reach. Use C-curve, which waits until 5 to 10 times.

earth? SHOCKfrom the body

Two wires, no earth

You see: a tingle from the outdoor unit or the grille

Run three wires, all the same size, and make sure the green one reaches a working earth at the board. A fault in the AC then trips the line instead of reaching you.

TAPED JOINT IN THE WALL

A joint inside the pipe

You see: the AC cutting out, a burning smell

A twisted, taped joint is the weakest point on the line and heats under an AC's load. Pull one unbroken length from the board to the point. Measure first, so the coil covers it.

Work out your line

Wire, MCB and metres for your AC

Put in the current from the name plate and how far the AC is from the board. You get the wire size, the MCB, the socket or point, the metres of each colour, and how much voltage the wire loses on the way.

Measure the way the pipe runs: up the wall, across, and down to the point, not a straight line across the room. 7.5 A is only a sample; put in your own plate figure.

Your AC line

Wire——
MCB, C-curve——
Connection——
Wire to buy, each colour——
Voltage lost on the wire——
Send this list on WhatsApp

Wire limits: V-Guard Classo+ in conduit. Voltage loss uses the standard maximum resistance for copper house wire (IS 8130: 7.98 Ω/km for 2.5 sq mm, 4.95 for 4 sq mm) and adds 1.5 m at each end for the board and the point. Price: Ask rate per 90 m coil, filled in from today's rate. Whole house: wiring calculator.

Questions people ask us

Short answers

Which wire size for a 1.5 ton AC? (1.5 ton AC ke liye kitne mm ka taar)

Read the current on the AC's name plate. If it is 12 A or less, which is the usual case for a home split, run 2.5 sq mm copper wire (phase, neutral and earth) with a 16 A C-curve MCB and a 16 A socket. If it is above 12 A and up to 16 A, run 4 sq mm with a 20 A C-curve MCB and a direct point.

Is 2.5 sq mm wire enough for a 2 ton AC?

Only if the plate shows 12 A or less. Above that, use 4 sq mm and a 20 A C-curve MCB. A 2-ton AC is where the plate most often changes the answer, so read it before you buy the wire.

Which MCB for an AC, 16 A or 20 A?

The wire decides. V-Guard Classo+ 2.5 sq mm carries 18 A in conduit, so it gets a 16 A MCB. A 20 A MCB goes only on 4 sq mm, which carries 24 A in conduit. Both must be C-curve.

Can I use 1.5 sq mm for a 1 ton AC?

No. 1.5 sq mm carries 13 A in conduit (Classo+), and it can't take the 16 A MCB and 16 A socket an AC point needs. It is for lights and fans. 2.5 sq mm is the minimum for any AC.

Can the AC share a line with the room's sockets or the geyser?

No. Every AC gets its own line from the board with its own MCB. Two ACs, two lines.

16 A socket or direct point?

On a 2.5 sq mm line with a 16 A MCB, a 16 A socket with its switch, which lets you unplug the AC for servicing. On a 4 sq mm line with a 20 A MCB, a direct point through a 20 A switch. Never a 6 A socket or an adapter.

What size earth wire?

The same as the phase wire: 2.5 sq mm on a 2.5 line, 4 sq mm on a 4 line. The standard wiring rule keeps earth the same size as the phase up to 16 sq mm.

Inverter AC or normal AC: does the wire change?

The rule doesn't change: go by the plate. Inverter ACs start more gently, but use the same wire, MCB and socket table above.

Will my home inverter run the AC?

Home inverter and battery sets of the size most houses here have are planned for lights, fans, TV and the fridge, not an AC. Keep the AC line off the inverter circuit. See what runs on an inverter.

Sashikesh Kumar
Diploma in Electrical, Tashya Ventures

Looks after wires, switchgear, inverters and pumps at our Reva Road store, Muzaffarpur. The wire and MCB figures on this page were checked against V-Guard's own product page and data sheet on 12 Nov 2026. Where a rule could go two ways, the page gives the safer one.

Where the numbers come from

  1. V-Guard, Classo+ house wire product page: current in conduit / clipped, 1.5 sq mm 13 / 16 A, 2.5 sq mm 18 / 22 A, 4 sq mm 24 / 29 A; 70 °C rating.
  2. V-Guard, Elegna MCB technical specification: 6 to 63 A, B type instant trip 3–5 In, C type 5–10 In, 10 kA, IS/IEC 60898-1. Warranty: Elegna product page.
  3. V-Guard, VGMW 500 Plus page: 15 A, 90–300 V input.
  4. V-Guard, Torio modular switches: dual shutter sockets.
  5. IS 8130 (standard figure): maximum resistance of flexible copper conductors at 20 °C, 7.98 Ω/km for 2.5 sq mm, 4.95 Ω/km for 4 sq mm. Used for the voltage loss.
  6. IS 732 wiring code (standard figure): protective (earth) conductor the same size as the phase conductor up to 16 sq mm.
  7. Standard figure: one ton of refrigeration ≈ 3.5 kW of cooling.

Send us your AC's name plate

A photo is enough. We'll send back the wire, MCB and socket for your line, with today's price, on WhatsApp.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com