P-trap 125×110 mm for the Orissa pan: the bend of water that keeps drain smell out of your bathroom
The P-trap is the bent pipe under an Orissa pan, and the water it always holds is what stops gas from the drain coming back up. Ours is 125 × 110 mm: the 125 mm end takes the pan's outlet, the 110 mm end joins the 110 mm SWR drain line. It leaves sideways, which suits a pan on the ground floor or on a sunken slab. Nearly every "smell from the pan" call we get is a trap that has dried out, been sucked empty or cracked, not a bad pan. Buy the trap with the pan: it is set in the bed before the tiles.
Price: Ask rate today, with GST bill. See today's sanitary rate or ask on WhatsApp for price and stock. A western toilet does not need this: its trap is built in (Cinco 300 for example).
Both hold water; they differ only in which way the pipe leaves
The P-trap turns and leaves sideways, into a drain pipe running under the floor. The S-trap turns and goes straight down, through the slab. For an Orissa pan on the ground floor, or on a sunken slab upstairs, the drain is laid sideways to the septic tank, so the P is the fit. If the pipe must drop through a slab with nothing to run sideways in, you need the S.
Published guides agree the P is the better one against smell: its sideways exit makes it harder for a rush of water to suck the seal out (studiomatrx calls the S "more prone to self-siphonage"). The bigger reason is simply that the P is what most pans need.
We keep the P 125 × 110 mm. An S version for a pan is not on the shelf, but we can order it for you; ask on WhatsApp for the time it takes. The full comparison, including the western toilet, is in S-trap or P-trap. If you are still choosing between a pan and a western toilet: Orissa pan or western.
Four steps, all before the tiles
The order is the same our fitters use for the Orissa pan; the bed and depth are the same as on Orissa pan or western.
Leave depth under the floor
The pan and its trap need depth below the tile. Ground floor: the earth filling gives it. Upper floor: plan a sunken slab, usually 250–450 mm deep, when the roof is cast.
Lay the 110 mm line with a fall
Run the 110 mm pipe to the septic tank with a fall away from the pan, and bring it to the point where the trap's 110 mm end will meet it. See 110 mm SWR pipes.
Set the trap, then the pan over it
Fit the 110 mm end to the line, then seat the pan's outlet in the 125 mm end. Bed both in sand and cement so nothing moves. Keep the pan's rim at the planned tile level.
Test with a bucket, then tile
Fill the trap and pour a bucket through. Look at both joints and watch that the water runs away and the trap keeps its water. A weeping joint is cheap to fix now, and means breaking the floor after tiling (usual practice).
A smell almost always means the water seal is gone
Three ways a trap loses its water, and what to do about each. Causes as described by studiomatrx and Prince Pipes; the repairs are usual practice.
Dried out
A bathroom nobody uses for some days: the water evaporates. Pour a mug or two into the pan. studiomatrx adds a spoon of cooking oil on top to slow the evaporation; we have not seen a maker publish that, so treat it as a home trick.
Sucked out
You hear a gurgle after a flush elsewhere on the line: the rush pulls the water from this trap. The cure is venting the drain stack (the pipe must end open above the roof) and a pipe of the right size. See bathroom smell.
Cracked or loose
The trap holds water for a day, then it is down again with no one using it. The trap or a joint leaks. This one needs the floor opened and the trap replaced.
Take the trap with the pan
Prices are from our latest bill and change often. Please confirm today's rate on WhatsApp or call before buying.
P-trap 125 × 110 mmSWR · 125 mm for the pan, 110 mm for the drain lineAsk today's ratewith GST bill CERA Calina Orissa panThe pan this trap goes underAsk today's ratewith GST bill 110 mm SWR pipe and bendsThe line the trap joinsAsk today's ratewith GST billToday's price and stock are on the sanitary rate page, or send "P-trap 125x110 for Orissa pan – price & stock?" on WhatsApp 90310 74624. We sell genuine fittings with a GST bill. Other pans: Orissa pans. Delivery is charged separately; ask for the amount for your site and see delivery.
Send a photo of the bathroom floor on WhatsApp before the bed is made and we will look at the drain position and depth with you.
Short answers
What is the P-trap 125×110 mm price in Muzaffarpur?
Our price for the day is on the sanitary rate page, with GST bill. We do not quote one from memory because it changes with the supplier's rate. Ask on WhatsApp for today's price and stock.
What do 125 and 110 mean?
They are the two socket sizes in millimetres: the 125 mm end takes the outlet of the Orissa pan and the 110 mm end joins the 110 mm SWR drain pipe. Hold the pan's outlet against the trap on our counter before you pay; makers' pan sheets (CERA's included) do not publish the outlet size.
Does a western toilet need this trap?
No. A floor-mounted western toilet such as the Cinco 300 has its S-trap inside the pan, so there is nothing to buy for the trap. This P-trap is for the Orissa pan, which has no trap of its own.
P-trap or S-trap for my Orissa pan?
Look at where the drain pipe goes. If it leaves sideways under the floor (ground floor, or a sunken slab upstairs), take the P. If it has to drop straight down through the slab, the S fits. Read S-trap or P-trap. We keep the P in stock; we can order the S for you, ask on WhatsApp for the time it takes.
How much water stays in the trap?
studiomatrx, an architecture tools site, gives about 50 mm as the usual water seal, and 75 mm where water evaporates fast. The trap refills itself with every flush; a dry bathroom is where it empties by evaporation.
Why does my bathroom smell even with a trap?
Most often the water in the trap has dried (a bathroom not used for days), been pulled out by a flush elsewhere, or leaked out of a cracked trap. The three tests are on this page, and bathroom smell goes through the rest.
Can the trap be changed after the floor is tiled?
Only by opening the floor, because the trap sits in the sand-cement bed under the pan. That is why we say: buy it with the pan, test it with a bucket, then tile.
Twenty years on sites around Muzaffarpur. The 125 × 110 mm sizes are the item's own; the water-seal figure and the causes of smell come from the guides named below. Fitting steps are usual practice on local sites, not a maker's rule.
Where the facts come from
- studiomatrx, Plumbing traps in India: typical water seal 50 mm (75 mm where evaporation is fast), P exits sideways and S downward, S more prone to self-siphonage, causes of dry or sucked-out traps.
- Prince Pipes, Ultrafit SWR traps: a trap holds water in its curved section to block sewer gas; P-trap fitted under Indian toilets. The page gives no sizes or seal depth.
- CERA, Calina Orissa pan S3010101 (530 × 425 mm); CERA does not publish the pan's outlet size, so check it against the trap's 125 mm end on our counter.
- Store facts: the item is stocked as "P TRAP 125MM X 110MM" at Rewa Road. Orissa pan fitting depth (250–450 mm sunken slab) is from Orissa pan or western.
Ask for the trap with your pan
Tell us the pan and whether the drain runs sideways or down, and we will confirm the trap, price and stock on WhatsApp.