हिंदी Call90310 74624
Home›Steel›Sariya rate
Sariya size guide · 12 mm

12 mm sariya: 10.66 kg a bar, where it goes, what a bundle weighs

The short answer
  1. 1 metre=0.888 kg
  2. 1 bar of 12 m=10.66 kg
  3. 1 quintal≈9.4 bars

12 mm is the all-round bar of a small house: slab, beam and, where the drawing says so, column. Locally it is "4 soot". You pay for weight, so ask for the rate per kg; the price of a piece is that rate × 10.66.

10.66 kg
One 12 m barStandard weight. A real bar sits within ±5% of it for the batch.
≈ 94
Bars to a tonne9.4 to a quintal. You get whole bars, so the bill's kg is what counts.
By kg
How we bill itWeighed in front of you; the bill shows kg and bars.
One 12 mm bar, drawn to length
A 12 mm sariya bar, its weight, and how it compares with other sizes A 12 metre bar marked every metre. Each metre weighs 0.888 kg, so the whole bar weighs 10.66 kg. Below, the cross-sections of 8, 10, 12 and 16 mm bars in proportion, with the weight of a 12 m bar of each: 4.74, 7.40, 10.66 and 18.96 kg. At the bottom, 9.4 bars make a quintal and about 94 make a tonne. 1 m = 0.888 kg 06 m12 m 12 m = 10.66 kg SIZES, IN PROPORTION 8 mm10 mm12 mm16 mm 4.74 kg7.40 kg10.66 kg18.96 kg weight of a 12 m bar · the dotted ring is the ribs 1bar10.66 kg 9.4bars1 quintal, 100 kg 94bars1 tonne, 1,000 kg
Weights: 0.888 kg per metre for 12 mm, from IS 1786. Jindal Panther's size table prints 0.889 kg and 10.67 kg; the 14 g gap is rounding. We use the standard's figure.
Where 12 mm goes

Slab, beam and column: what the makers say and what the drawing decides

12 mm is a main bar for the frame of a house of one to three floors. It is not a ring bar and not usually the heavy bar of a footing.

Usual small-house practice · the drawing decides
Where 12 mm bars sit in a column, a beam and a slab Column section with four 12 mm main bars at the corners and a ring around them. Beam section with two 12 mm bars on top and three at the bottom, inside a ring. Slab edge view with 12 mm main bars along the bottom and thinner distribution bars across them. Column 4 bars of 12 mm at the corners, inside a ring of 6 or 8 mm. Taller or heavier columns go to 16 mm. Beam 2 on top, 2 or 3 below 12 mm for short spans and plinth or lintel beams. Main beams and long spans take 16 mm. Slab 12 mm main bars at the bottom, spaced as drawn; lighter 8 mm bars across them. 10 mm is the other usual choice. 12 mm bar ring or distribution bar
Sketch, not a design: bar counts are the common small-house pattern. Your engineer's bar bending schedule is what you build from.
Tata Tiscon (Aashiyana size list): "primary reinforcement in beams, columns, slabs for medium size structures."
JSW Neosteel (bar sizes guide): slabs, beams and residential construction. Columns are not named for 12 mm.
Jindal Panther (12 mm guide): primary beams and slabs; its heavy-load column bar is 16 mm.
The makers differ on columns, so we take the careful reading: use 12 mm in a column only where your drawing shows it, and ask your engineer before going lighter anywhere. A shop cannot size a bar for your house, and we will not guess it for you.
  • Not for ringsRings (stirrups) are 6 or 8 mm. See 8 mm.
  • Not for the heavy placesFootings, main beams and tall columns usually step up to 16 mm. See 16 mm.
  • Tie it with binding wireLap lengths and cover come from the drawing. Sizes of wire: binding wire.
How many bars in a bundle

The sources disagree, so work from the weight

Search this and you get anything from 5 bars to 12. Three guides, three answers. The bundle count matters less than it looks.

What a bundle of 12 mm weighs, by number of bars
Weight of a bundle of 12 mm bars for 5, 7, 10 and 12 bars At 10.66 kg a bar: 5 bars weigh 53.3 kg, 7 bars 74.6 kg, 10 bars 106.6 kg and 12 bars 127.9 kg. Jindal Panther's guide says 5 to 7 bars a bundle; Comaron's says 10 or 12. 5 bars7 bars10 bars12 bars 53.3 kg74.6 kg106.6 kg127.9 kg Jindal Panther guide: 5 to 7 bars Comaron guide: 10 or 12 bars Our bill: kg of 12 mm, plus the number of bars. Same kg, same money, whatever the bundle.
Bundle weight = bars × 10.66 kg, at standard weight. Tata nexarc lists bundle size as "varies by manufacturer" for every size.

Why they differ. Each mill ties its own bundles. None of the three guides says which mill's bundle it is describing.

Why it hardly matters. We sell by weight. A bundle of 10 and a bundle of 12 at the same kg cost the same. What the count changes is only how the steel is stacked and handled.

What to do. Tell us the kg from your engineer's list, not the bundle count. If you want whole bundles to avoid cutting a tied bundle, ask us the count on the bundle in the yard and we will tell you before you pay.

Read the bundle tag. The maker's tag on each bundle carries the brand and grade. Saluja Gold prints the grade on every bundle tag; check that the grade matches your drawing. More on counts: sariya bundle mein kitna.
When the truck arrives

How to check a 12 mm delivery

A bar that is a little light is allowed. A bundle that is a lot light is not. Three checks, none needing special tools.

1
Read the bar and the tagThe brand and grade are embossed on the bar, and Jindal Panther's own genuine-check page tells buyers to look for them. The tag on the bundle should match the bill: Tata Tiscon 550SD, or the grade on the Saluja Gold tag.
2
Weigh the lot, not one barBars, weighed together on the weighbridge or the shop scale, should come to the bill's kg. Compare with bars × 10.66 kg: a 10-bar load should be near 106.6 kg.
3
Measure the length12 m is 39.4 ft. A bar cut short is the same price per piece for less steel. Tape one or two bars along the road.
What is allowed (IS 1786)
CheckLimit12 mm, 12 m bar
A whole batch±5%10.12 to 11.19 kg
One bar alone−6%not below 10.02 kg
10 bars±5%101.2 to 111.9 kg

These are the BIS limits for bars over 10 up to 16 mm.

What it is called on site

12 mm is "4 soot"

A soot is an eighth of an inch. The thekedar says the number of eighths; the shop sells the nearest metric bar.

2 soot6 mm
3 soot10 mm
4 soot12 mm
5 soot16 mm

4 soot is ½ inch, which is 12.7 mm, and 12 mm is the bar made for it. The gap is under a millimetre, but 12 mm is the size on the drawing and the bill, so ask for it by mm to be safe. The full list is in soot to mm. Usual local speech; the soot names are not in any standard.

Short of 12 mm?

Can 10 mm or 16 mm stand in for 12 mm?

Only if your engineer redraws it. The steel in a bar goes with the square of its diameter, so the swap is never one for one.

BarSteel areaTo equal one 12 mm bar
8 mm50 mm²2.25 bars
10 mm79 mm²1.44 bars
12 mm113 mm²1 bar
16 mm201 mm²0.56 bar

One 12 mm bar holds as much steel as about 1.44 bars of 10 mm, or 0.56 of a 16 mm bar. You cannot buy half a bar, and the spacing in a slab, the room in a beam, and the lap lengths all change with the diameter.

Do not swap on site. A drawing that says 12 mm @ 150 does not become 10 mm @ 100 by arithmetic alone. Send your engineer the stock you have and let them redraw it. Our sariya calculator turns the drawing's kg into bars of each size.
Kg and bars

How many 12 m bars is my kg, and how many bundles?

Type kg or bars; the other fills in. The price per piece is the day's rate per kg × 10.66.

Your 12 mm

Value
Weight—
12 m bars—
Quintal—
Bundles—
Cost at today's rateAsk rate

Bars are rounded up. Standard weight, 10.66 kg a bar; the real weight is what we weigh at the store. Today's rate: sariya rate board.

Ask for today's 12 mm rate
Order from us

12 mm sariya at our Reva Road store

In both brands, weighed and billed by kg. Every size and every length can be ordered; ask on WhatsApp for the time it takes.

Today's price for both brands and every size: sariya rate board, GST included. Weights for every size: weight per metre. Per kg, quintal or piece: how to convert.

Questions people ask us

Short answers

12 mm sariya ka rate kya hai?

It moves through the day, so it is on our rate board: per kg, per quintal and per 12 m piece, GST included, with the time of the last update. To get the price of one piece yourself, multiply the per-kg rate by 10.66.

How many kg is one 12 mm sariya of 12 metres?

10.66 kg, from the standard weight of 0.888 kg a metre in IS 1786. Real bars differ a little within the allowed limits, which is why we weigh.

12 mm sariya 1 bundle mein kitna hota hai?

Guides online say 5 to 7 (Jindal Panther), 10 or 12 (Comaron) or "varies" (Tata nexarc), and each is tying a different mill's bundle. We bill by kg, so the count does not change what you pay. Ask us the count on the bundle you are buying. See bundle count.

How many 12 mm bars make a quintal or a tonne?

About 9.4 bars of 12 m make a quintal and about 94 make a tonne, at standard weight. You get whole bars, so the bill's kg is the figure that counts.

4 soot kitne mm ka hota hai?

A soot is ⅛ inch, so 4 soot is ½ inch, 12.7 mm. The bar sold for it is 12 mm. Other soot sizes: soot to mm.

Is 12 mm sariya used in the column, beam or slab?

In all three where the drawing says so. Tata Tiscon lists 12 mm as a main bar in beams, columns and slabs of medium structures, JSW lists slabs and beams, and Jindal Panther puts its column bar at 16 mm. Use the size and number on your engineer's drawing.

How long is a 12 mm sariya in feet?

A standard bar is 12 metres, which is 39.4 feet. Some pages call it 40 feet; a true 40 ft bar would be 12.19 m and weigh about 10.8 kg.

Can I use 10 mm bars instead of 12 mm?

Only if your engineer changes the drawing. One 12 mm bar equals about 1.44 bars of 10 mm by steel area, and spacing and lap length change with it.

Do you cut 12 mm bars to length?

Yes. Cutting and delivery are charged separately from the steel; ask for the amount for your site. See cutting and delivery.

Abhishek Ranjan
Civil Engineer (Diploma), Tashya Ventures

Looks after cement, steel and building questions at our Reva Road store, Muzaffarpur. The weights and limits on this page were checked against IS 1786 and the makers' published sheets on 12 Nov 2026. Where makers differ, we say so and use the careful figure.

Where the numbers come from

  1. Bureau of Indian Standards, IS 1786:2008: 0.888 kg per metre for 12 mm; mass tolerance ±5% on a batch and −6% on a single bar for sizes over 10 up to 16 mm.
  2. Jindal Panther, TMT bar size table: 0.889 kg per metre and 10.67 kg per 12 m bar; and its 12 mm length and weight guide: 0.888 kg, 5 to 7 bars a bundle, 12 mm for primary beams and slabs.
  3. Comaron, 12 mm ka sariya 1 bundle mein kitna hota hai: bundles of 10 or 12 bars.
  4. Tata nexarc, steel bar weight chart: 10.66 kg a 12 m bar, 94 bars a tonne, bundle size "varies by manufacturer".
  5. Tata Steel Aashiyana, Tata Tiscon rebars: 12 mm as primary reinforcement in beams, columns and slabs for medium-size structures.
  6. JSW Neosteel, TMT bar sizes: 12 mm for slabs, beams and residential construction; 0.888 kg per metre.

Send us the kg or the bars you need

We'll send today's 12 mm rate on WhatsApp, per kg, per quintal and per piece.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com