हिंदी Call90310 74624
Home›Steel›Tata Tiscon
Sariya compared · we stock both

Tata Tiscon vs Saluja Gold: the price gap per kg, and when each bar makes sense

The short answer

Both are BIS-licensed TMT bars and both sit in our yard. Neither is fake or weak. They are built for different jobs.

Saluja GoldBoundary wall, shed, tank base, a single-storey house that will stay single-storey. Cheaper per kg, meets IS 1786 with room to spare.
Tata TisconEngineer-designed frame, any floor planned above, or earthquake detailing on the drawing. Higher strength, more stretch, tighter weight and chemistry.

If the drawing names a grade, buy that grade. Everything else on this page is for when it doesn't.

570 / 520
Yield strength, MPaTata 550SD vs Saluja Fe 500, from each maker's sheet.
16% / 15%
Stretch before breakingClose. The bigger gap is in grade, chemistry and checks.
×3,500–4,000
The gap on a housePer-kg gap × this = Tata's extra on a 1000 sq ft floor.
Today's gap, 12 mm: Ask rate per kg sariya rates
Two bars, side by side
Tata Tiscon 550SD and Saluja Gold Fe 500 compared Yield strength 570 against 520 MPa, with IS minimums 550 and 500 marked. Stretch before breaking 16 against 15 percent. Sulphur plus phosphorus 0.070 against 0.105 percent, lower is cleaner. Tata is sold by the 12 metre piece with a holographic tag on every bundle; Saluja is sold by weight with the ISI mark and licence number rolled on the bar. TATA TISCON 550SD SALUJA GOLD · ISI Tata Tiscon 550SD Saluja Gold Fe 500 (our stock) Yield strength, MPa load where the bar stops springing back · higher = stronger 570* 520 IS 550D: 550 IS Fe 500: 500 Stretch before breaking, % elongation · higher = more warning before it snaps 16 15 IS 550D: 14.5 IS Fe 500: 12 Sulphur + phosphorus, max % impurities · lower = cleaner, more ductile, welds better 0.070 0.105 SOLD BY 12 m piece, Tata's RCP weight (kg), bundles PROOF name + grade embossed, holographic tag ISI mark, CM/L-5801867 on leaflet Yellow ticks: the IS 1786 minimum each bar is tested against.
Bars start at zero, so the differences look as small as they are. *Tata's sheet marks 570 as the value 95% of its test results reach; the guaranteed floor is IS 1786's 550. Sources: Tata Tiscon 550SD brochure (2026), Saluja Gold comparison leaflet (2024).
The makers' own figures

Both product sheets, row by row

Every figure below is copied from the maker's own sheet, not from a dealer site or a list of "top 10 brands". Our Saluja Gold comes in on Birla Pivot's bills as Fe 500, so that is the column we compare.

Tata Tiscon 550SDSaluja Gold Fe 500
Strength
GradeFe 550D, "super ductile"6 mm in Tata's range is Tiscon 500DFe 500maker also rolls Fe 500D, Fe 550, Fe 550D, Fe 600 (SG600)
Yield strength, minimum570 MPa95% of test values; IS floor 550520 MPaIS floor 500
Tensile strength, minimum655 MPaand at least 15% above yield610 MPaIS asks 545
Tensile ÷ yieldthe reserve after yielding1.15 to 1.25the band IS 13920 asks for1.17IS Fe 500 asks ≥ 1.08
Stretch (ductility)
Elongation before breaking16%IS 550D asks 14.515%IS Fe 500 asks 12
Stretch at peak load (Agt)5%not givenFe 500 is not a "D" grade
Chemistry
Sulphur + phosphorus, max0.070%0.105%
Carbon, max0.25%0.28%
Buying
Weight tolerance, 12 mm± 3%± 5% up to 10 mm− 5% / + 2%− 7% / + 3 to 4% up to 10 mm
How it is pricedBy the 12 m piece, at Tata's Recommended Consumer Price, shown at dealersBy weight; the maker posts a Bihar price list. Bundles: 12 mm = 5 pieces, 16 mm = 3
Proof it is genuine"Tata Tiscon" and grade embossed on every bar; holographic "Tag of Trust" on every bundle"SALUJA GOLD", size and ISI mark rolled on the bar; IS 1786 licence CM/L-5801867
Made fromIron ore → blast furnace → BOF steel, Tata's plantsOwn sponge iron plus scrap → own billets → rolling mill, Giridih, Jharkhand
ExtrasGreenPro certified ("India's first"); doorstep test lab, not offered in BiharISO 9001 plant; selling in Bihar since 2014
Sizes in our yard6, 8, 10, 12, 16 mm20 and 25 mm: we order them6, 8, 10, 12, 16 mm20 to 32 mm and other grades: we order them
Tata's 570 is not a hard minimum.Its sheet footnotes 570 as the figure "95% values are within". What every bar must meet is the IS 1786 floor of 550. It is still a strong figure.
Saluja's sheet has a labelling slip.Its chemistry table heads a column "Fe 500 D", the mechanical table heads the same column "Fe 550 D". No mechanical figures are printed for Fe 500D. Ordering Fe 500D? Ask for the mill test certificate.
Tata's 6 mm is a different bar.Tata's brochure says 6 mm is Tiscon 500D, not 550SD. That's fine for rings, but don't expect 550SD figures from it.
Three numbers that matter

What yield, stretch and the "D" actually do in your house

Pull a bar and it springs back, then gives and stretches, then breaks. The curve shows both bars from their makers' minimum figures.

Load against stretch for the two bars Schematic curves. Saluja Gold Fe 500 yields at 520 MPa, rises to 610 and breaks at 15 percent stretch. Tata Tiscon 550SD yields at 570, rises to 655 and breaks at 16 percent. The dashed line is the IS Fe 500 minimum of 500 MPa. The area under each curve is the energy the bar can soak up before breaking. 05%10%15% 500300100 stretch → load, MPa ↑ IS Fe 500 floor, 500 yields at 570 yields at 520 breaks at 16% breaks at 15% shaded area = energy soaked up before breaking (Saluja shown)
Schematic, drawn through each maker's published minimums: yield, tensile strength and elongation. Real test curves vary bar to bar.

1Yield: the working limit

Up to its yield load a bar springs back like a spring. Engineers design so everyday loads stay well below it. A higher yield lets a design use fewer kg, but only if the engineer designs for it. Swap a 550 bar into a 500 design and you just get extra margin.

2Stretch: the warning

Past yield, a good bar stretches a long way before it snaps. In an earthquake that stretching soaks up the shaking, and the cracks you see are a warning instead of a sudden collapse. Here the two bars are close: 16% against 15%.

3The "D": a tested promise

A "D" grade (Fe 500D, 550D) is tested for stretch at peak load and has tighter limits on sulphur and phosphorus. Tata 550SD is a D bar. Our Saluja stock is Fe 500, not 500D. Its stretch is close to a D bar's, but it isn't sold or tested as one.

Muzaffarpur is in a high earthquake zone (zone IV under IS 1893). For a framed house here, engineers usually ask for a D grade. More on what Fe 500, 500D and 550D mean and sariya for Muzaffarpur's earthquake zone.

What the gap costs

Rupees per kg look small. Here is the gap on your house.

Tata is priced by the 12 m piece; Saluja is priced by weight. Our sariya rate page puts both in rupees per kg, so the gap is a fair comparison.

1000 sq ft floor takes 35 to 40 quintal of steel, so every rupee of gap per kg adds 3,500 to 4,000 rupees 1000 sq ft 35–40 qtl 3.5–4 kg per sq ft each ₹1/kg of gap ₹3,500– 4,000 per floor

Type the gap from today's sariya rates. Steel uses the thumb rule from our sariya calculator: 3.5 to 4 kg per sq ft of built-up area. Your engineer's bar schedule gives the real figure.

Today, per kgTataSalujaGap
8 mmAsk rateAsk rateAsk rate
10 mmAsk rateAsk rateAsk rate
12 mmAsk rateAsk rateAsk rate
16 mmAsk rateAsk rateAsk rate
From our sariya rate page. Cutting and delivery are charged separately; ask for the amount for your site (delivery).

Your house

Steel for the house—Area × floors × 3.5 to 4 kg
Tata's extra for every ₹1/kg of gap—The same number as the kg. Double the gap, double the extra.
Tata's extra at your gap—Type today's gap per kg to see it.
Ask us for both prices on WhatsApp

Put the extra next to the cost of the whole house. Steel is only one line of it, and the Tata-over-Saluja gap is a slice of that line. Whether that slice is worth it depends on the building, not on the brand: see the next section. Stage-by-stage kg: sariya calculator.

How we advise at the counter

Which bar for which building

The question is not "which brand is better". It is "how hard will this building be tested, and will it grow?"

light load · no floor above
Saluja Gold

Boundary wall, gate pillar, shed, tank base

Loads are light and simple. A BIS-licensed value bar does the job, and paying for Tata buys you little here.

one floor, and it stays one floor
Saluja Gold is sensible

Single-storey house, no plan to build up

Fine with a certified bar laid to a sound plan: rings closed with 135° hooks, cover blocks, proper lap. Be honest with yourself about "never".

floor to come later
Tata Tiscon

Ground floor now, upper floor later

The columns and footings poured today must carry the floor you add in five years. Steel inside a cast slab can't be changed, so decide before dhalai.

Fe 550D framed · engineer's drawing
Tata Tiscon, or the drawing's grade

Engineer-designed frame, G+1 and up

Columns and beams carry everything, and the drawing often calls for earthquake detailing (IS 13920). That code asks for the 1.15 to 1.25 tensile-to-yield band that Tata's sheet promises.

Two rules that beat any brand choice. One: if the drawing names a grade, buy exactly that grade and ask for it on the bill. Two: never mix brands or grades inside one column, beam or slab. Saluja for the boundary wall and Tata for the house frame is fine.
The question everyone asks

"My neighbour used a cheaper bar, and his house is fine."

Everyday load against the day of a strong earthquake Two houses that look the same. On an ordinary day, both bars work far below their yield point. On the day of a strong earthquake, columns are pushed past yield, and what keeps the house standing is how far the bar can stretch, along with good rings and concrete. Every day, for years The day the ground shakes load in the bar, against its yield yield both bars: well below yield load in the bar, against its yield yield past yield: stretch decides
Schematic. On ordinary days a sound house uses a small part of any certified bar's strength. A strong earthquake is when the bar's stretch, the rings and the concrete are all tested at once.

He may well be right. A house shows nothing about its steel until it is tested. On ordinary days, a sound single-storey house uses only a small part of a certified bar's strength, and that can go on for decades. That is why the cheaper bar "looks fine".

The test comes on two days: the day you add a floor, and the day a strong earthquake comes. North Bihar has had big ones (1934 and 1988). On those days the bars in the columns get pushed past yield. Then what counts is how far they can stretch without snapping. That is where the "D" grade, low sulphur and phosphorus, and the 1.15 to 1.25 reserve earn their price.

Brand isn't the whole story, though. A Tata bar with open rings, no cover blocks and weak concrete will do worse than a Saluja bar laid properly. Spend on detailing first. Rings with 135° hooks, closer spacing near joints, a proper lap and good curing matter as much as the bar.

So the honest answer: if your house will stay single-storey and is simple, the cheaper certified bar is a fair choice. If it will grow, or an engineer has drawn a frame, the extra is a small slice of the house cost. Steel in a cast slab cannot be upgraded later.

Send photos of the bars and rings on WhatsApp before dhalai, and we will look at them with you.

When the truck comes

Check the marks, then weigh one piece

The per-kg comparison only holds if each bar is full weight. Weigh one 12 m piece per size. Each maker publishes how light it may be.

One 12 mm bar, 12 m long: allowed weight
Allowed weight range of a 12 metre, 12 mm bar Standard weight 10.66 kg. IS 1786 allows 10.13 to 11.18 kg. Saluja Gold's sheet allows 10.13 to 10.86 kg. Tata's plus or minus 3 percent works out to 10.34 to 10.98 kg. 10.010.511.0kg standard 10.66 kg IS 1786: ± 5% 10.1311.18 Saluja Gold: − 5% / + 2% 10.1310.86 Tata Tiscon: ± 3%
Saluja's range is printed in its leaflet. Tata's range is worked out from its published ± 3% for 12 and 16 mm. Standard weight per metre = d² ÷ 162.
SizeStandard, 12 m pieceSaluja allowsTata allows
8 mm4.74 kg4.40–4.924.50–4.98
10 mm7.40 kg6.89–7.627.03–7.77
12 mm10.66 kg10.13–10.8610.34–10.98
16 mm18.96 kg18.01–19.3218.39–19.53

Standard weight per metre, labelled as such. Saluja figures from its leaflet; Tata figures worked out from its ± 5% (up to 10 mm) and ± 3% (12, 16 mm). More: sariya weight per metre.

Tata Tiscon: look for

  • "TATA TISCON" and "550SD" embossed along every bar
  • A holographic Tag of Trust on every bundle
  • Priced per piece at Tata's RCP, shown at the dealer

Saluja Gold: look for

  • "SALUJA GOLD", the size and the ISI mark rolled on the bar
  • BIS licence CM/L-5801867 (from the maker's leaflet) on the tag
  • Bundle count: 8 mm 12 pieces, 10 mm 8, 12 mm 5, 16 mm 3

Ask for the brand, grade and size on the bill. More checks: real or fake sariya.

Questions people ask us

Short answers

Is Saluja Gold sariya good? (Saluja Gold kaisa hai)

It is a BIS-licensed TMT bar to IS 1786 (licence CM/L-5801867 on the maker's leaflet), made at Giridih, Jharkhand, from the company's own sponge iron and billets. For Fe 500, the grade we stock, the maker publishes a minimum yield of 520 MPa and 15% elongation, above the IS minimums of 500 and 12%. It suits boundary walls, sheds and single-storey houses that will stay single-storey.

What is the difference between Tata Tiscon 550SD and Fe 500D?

Fe 500D is the IS 1786 grade with a 500 MPa minimum yield and 16% elongation (standard figure). Tata Tiscon 550SD is Tata's super-ductile Fe 550D bar: its sheet gives 570 MPa yield, 16% elongation, 5% stretch at peak load and a tensile-to-yield ratio of 1.15 to 1.25. Fuller answer: Fe 500, 500D and 550D.

Why pay more when my neighbour used a cheaper bar and it's fine?

For everyday loads he is probably right. What the costlier bar buys is margin for the day the house is tested: a strong earthquake, or a floor added later. If neither applies, the cheaper certified bar is fair. If either does, Tata's extra on a 1000 sq ft floor is about 3,500 to 4,000 times the per-kg gap. The full answer is above.

Which is the best sariya in Bihar?

There is no single best. Buy the grade your engineer's drawing names. For a framed house, upper floors or earthquake detailing, choose a super-ductile bar such as Tata Tiscon 550SD. For a boundary wall, shed or simple single-storey house, a BIS-licensed value bar such as Saluja Gold is sensible.

Can I build a two-storey house with Saluja Gold?

Ask your engineer, and buy the grade on the drawing. Our stock is Fe 500. If the drawing asks for Fe 500D or 550D, we can order Saluja's D grades, or you can take Tata 550SD from stock. For a frame of G+1 and up in Muzaffarpur, we advise a D grade.

Saluja Gold vs Kamdhenu, or Tata Tiscon vs Captain: which is better?

Use the method on this page: put the same rows side by side from each maker's own sheet for the same grade. Compare yield, tensile strength, elongation, sulphur plus phosphorus, weight tolerance and the BIS licence number. Don't trust a "top 10" list without figures. We keep Tata Tiscon and Saluja Gold in stock and can order other brands; ask on WhatsApp for the time it takes.

Can I mix Tata and Saluja in one house?

Not inside the same column, beam or slab. Keep one brand and grade per member so the engineer's design holds. Saluja for the boundary wall and Tata for the house frame is fine.

Is the Tata rate per piece or per kg?

Tata sells 550SD by the 12 m piece at its Recommended Consumer Price. Saluja is priced by weight. To compare fairly, our sariya rate page shows both per kg, per quintal and per piece.

Abhishek Ranjan
Diploma Civil Engineer, Tashya Ventures

Handles cement and steel at our Reva Road store, Muzaffarpur, where both bars on this page are sold. Every figure here was copied from the maker's own sheet on 12 Nov 2026. Where a sheet is unclear or contradicts itself, this page says so.

Where the numbers come from

  1. Tata Steel, Tata Tiscon 550SD brochure (2026): technical specifications table (570 MPa yield with the footnote "95% values are within this limit", 655 MPa tensile, UTS/YS 1.15–1.25, 16% elongation, 5% Agt, S 0.035, P 0.035, S+P 0.070, C 0.25, CE 0.61), sizes 6* to 25 mm with "*6mm is currently available in Tata Tiscon 500 D", sale by 12 m piece, RCP, Tag of Trust, blast furnace and BOF route.
  2. Tata Steel, Tata Tiscon 550SD product page: weight tolerance ± 5% up to 10 mm and ± 3% for 12 and 16 mm, GreenPro, IS 13920 ratio, embossed brand and grade.
  3. Saluja Steel & Power, Saluja Gold comparison chart leaflet (Nov 2024): chemical and mechanical tables for Fe 500, Fe 550, Fe 500D/550D and Fe 600 against IS 1786; weight tolerances and bundle counts; IS 1786 licence CM/L-5801867; works at Mahtodih, Tundi Road, Giridih; sponge iron, SMS and rolling mill; selling since 2014.
  4. Saluja Steel & Power, salujagold.com: grades Fe 500, Fe 550, Fe 500D, Fe 600; state price lists including Bihar.
  5. IS 1786:2008 minimums (yield, tensile, elongation) as printed in the IS columns of both makers' tables. Fe 500D elongation (16%) is a standard figure.
  6. Grade of our Saluja Gold stock: Birla Pivot purchase bills, Oct 2026 (Fe 500). Steel per sq ft: the thumb rule used in our sariya calculator.

Not sure which to buy?

Send your plan or drawing on WhatsApp. We'll tell you which bar, which sizes and how many kg, with today's price for both.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com