हिंदी Call90310 74624
Home›Steel›Asli ya nakli
Genuine or fake · sariya

Asli sariya ki pehchaan: read the bar, check the licence, weigh one piece

The short answer

Genuine TMT sariya proves itself in three ways. A fake, or a bar sold as something it is not, fails at least one of them.

  1. Marks rolled into the steelBrand, grade and a six-digit number, raised on the bar and repeated at least every 3 m. Paint or a sticker does not count.
  2. A licence you can checkThe bundle tag carries the ISI mark and a CM/L number. Type it into the free BIS Care app; the maker it names must be the one on the bar.
  3. Full weightWeigh one 12 m bar. A little light is allowed. About 30% light means a thinner bar sold as the bigger size.
3 m
Longest gap between marksBIS rule for every certified bar
2 min
To check a licenceBIS Care app, free, from the government
−6%
Lightest one 12 or 16 mm bar may be−8% for 6, 8 and 10 mm (IS 1786)
What a certified bar carries
Marks on a certified TMT bar and its bundle tag A 12 metre bar with marks repeated at least every 3 metres. Close up, the bar shows brand, grade Fe 500D and a six-digit number 41 2345. The bundle tag shows maker, size 12 mm, grade, cast number, the ISI mark with IS 1786 and licence CM/L-7102345. The last four digits 2345 on the bar match the end of the licence number. One 12 m bar ≤ 3 m … and again, to the end BRANDBRAND Fe 500DFe 500D 41 234541 2345 1 2 3 Brand Grade Six digits maker's nameor trade mark Fe 500, 500D,550D, 550SD… 2: BIS office4: end of licence BUNDLE TAG MAKER'S NAME Size 12 mm · Grade Fe 500D Cast / heat no. 45821 ISI IS 1786 CM/L-7102345 licence no. last 4match Example numbers, not a real licence
Drawn larger than life; the numbers are an example, not a real licence. Marks on the bar: BIS product manual for IS 1786. Tag contents: IS 1786 and the makers' tags.
Check 1 · the bar itself

Three things must be rolled into the steel

BIS, which licenses every ISI-marked bar, tells makers to roll these onto the bar while it is hot, or mark them some other permanent way, at least once every 3 metres. So a 12 m bar shows them four times or more. Look along the whole bar, not one end.

1The brand

The maker's name or trade mark, raised in the steel between the ribs. Tata Tiscon rolls "TATA TISCON"; Saluja rolls "SALUJA GOLD".

TATA TISCON · SALUJA GOLD

2The grade

The strength grade from IS 1786. It must match what your engineer wrote and what the bill says. A bar marked Fe 500 is not a Fe 500D or 550D bar, even if the seller says so.

Fe 500 · Fe 500D · Fe 550D · 550SD

3A six-digit number

The first two digits stand for the BIS office; the last four are the end of the maker's licence number. That is what lets you tie a bar to the tag and to the app in the next check.

41 2345 → CM/L-…2345

Raised, not printed. Rub the mark with your thumb. Rolled marks are part of the steel and don't come off; paint, stencil or chalk does. Many makers also roll the ISI mark on the bar. Where it is missing from the bar, it must be on the tag. For what Tata's own bar and tag look like, see Tata Tiscon at our store.

Check 2 · tag and licence

Read the tag, then check the licence in two minutes

Every bundle should carry a tag with the maker, size, grade, cast (heat) number and the ISI mark with the CM/L licence number. Faking a mark is easy. Faking a licence that the government's app confirms, under the right maker's name, is not.

  1. Read the tag on the bundleSize and grade on the tag must be the same as on the bars inside. Note the CM/L number printed beside the ISI mark.
  2. Open the BIS Care appIt is free from the Bureau of Indian Standards, on Android and iPhone. Choose Verify Licence Details, type the CM/L number, press Go.
  3. Read three linesThe licensee's name must be the maker on the bar. The standard must be IS 1786 (steel bars for concrete). The licence must be in force, not expired or cancelled.
  4. Match the last four digitsThe six-digit number on the bar should end with the last four digits of the CM/L number.
    If the app shows another company, another product, a dead licence, or no result: don't take the bars. You can report it in the same app under Misuse of ISI Mark.
  5. For a big order, ask for the test certificateBIS requires every certified consignment to go out with the maker's test certificate showing the ISI mark, cast number, grade, size and test results. Your engineer can check the cast number on it against the tag.
The check, on your phone
Checking a CM/L licence number in the BIS Care app Phone screen: Verify Licence Details, the CM/L number typed in, Go pressed. The result shows the licensee name, the standard IS 1786 and status Operative, each with a green tick. BIS CARE Verify Licence Details Type the CM/L number 7102345 Go LicenseeStandardProductStatus Maker on the bar?IS 1786Steel bars, concreteOperative Different name? Don't buy. 1 2 3
Schematic of the BIS Care app's licence check. Option name from BIS's own page about the app; the number is an example.
Tata TisconLook for the holographic Tag of Trust on the bundle, besides the embossed brand and 550SD. Tata's dealer locator and toll-free line answer for any seller, us included. Full detail: Tata Tiscon at our store · real or fake Tata Tiscon.
Saluja GoldSaluja's own leaflet gives its IS 1786 licence as CM/L-5801867. Put that in the app and compare with the tag on your bundle. The two bars side by side: Tata Tiscon vs Saluja Gold · checking Saluja Gold.

6 mm rings: the government's compulsory-ISI order for TMT bars covers 8 mm and thicker. Bars under 8 mm are left out of it, so for 6 mm go by the brand mark, the weight and the bill.

Check 3 · weight

Weigh one 12 m piece: the line it must not cross

The common cheat isn't a bar made of rubbish. It is a thinner bar sold under the bigger number. It looks almost the same on the truck but carries about a third less steel. A shop scale catches it in a minute.

SizeStandard weight, 12 m pieceLightest one piece may beIf it is really the next size down
6 mm2.67 kg0.222 kg per metre2.45 kgsmallest size
8 mm4.74 kg0.395 kg per metre4.36 kg2.67 kg (a 6 mm bar)
10 mm7.41 kg0.617 kg per metre6.81 kg4.74 kg (an 8 mm bar)
12 mm10.67 kg0.889 kg per metre10.03 kg7.41 kg (a 10 mm bar)
16 mm18.96 kg1.580 kg per metre17.83 kg10.67 kg (a 12 mm bar)

Standard weight per metre = d² ÷ 162. "Lightest one piece" is the single-bar limit in IS 1786 (8% under for up to 10 mm, 6% for 12 and 16 mm). Bars weighed together as a lot have tighter limits, and Tata publishes tighter ones for Tiscon.

How to do itPick a bar from the middle of the bundle, not the top. Check it is a full 12 m with a tape. Weigh it, and compare with the red column. Below the red figure: send it back. Near the last column: you have been sold the next size down. Every size, a weight checker and tolerances in detail: weigh your sariya · sariya weight per metre.
What to watch for

Six tricks, and how each one shows up

None of these needs a lab to catch. Each fails one of the three checks above.

Plain bar sold as a brand

You see: ribs, but no name, grade or number anywhere along it

Often called "local" or re-rolled bar. Without marks there is nothing to check and no one to answer for it. Walk away.

Next size down, sold as the bigger one

You see: the bar is about 30% light on the scale

10 mm sold as 12 mm, 8 mm as 10 mm. Your slab gets far less steel than the drawing. Only the scale shows it; the eye does not.

Good bars outside, plain bars inside

You see: marked bars on the outside of the bundle only

Pull two bars from the middle and read them. Count the pieces and weigh the bundle against the bill.

A painted or stencilled mark

You see: a flat mark that smudges or scratches off

Real marks are raised steel, rolled in while the bar is hot. They feel like part of the rib pattern.

Tag, bar and bill don't agree

You see: the size, grade or brand differs between them

A tag can be moved from another bundle. The bar's own marks and the GST bill must say the same brand, size, grade and kilograms.

Old stock with deep rust

You see: pits, flakes, ribs eaten away

Light brown rust that rubs off is normal on bars kept outside. Deep pitting and peeling are not: the bar has lost steel. Reject it.

Optional · on an offcut

The bend test: what a mason can do on site

Good TMT bends without cracking. That is what lets it hold on in an earthquake instead of snapping. A brittle bar shows itself the moment it is bent.

  1. Take an offcut, not a bar for the slabA 1 to 1.5 ft piece left over from cutting.
  2. Bend it round a pipe, all the way backUse a pipe about five times the bar's thickness: for 12 mm, a pipe about 60 mm across (2-inch GI). Bend it into a U, 180°. The code's own bend test uses a former of 4 to 5 times the bar size depending on grade, so a 5× pipe is fair to every bar we sell.
  3. Look at the outside of the bendSmooth, perhaps a little wrinkled: pass. Cracks or a split across the ribs: fail. Stop using that lot and call the seller.

Bend it once, cold, by hand or with a bending key. Don't heat it, and don't use the bent piece in the work. A real strength test needs a lab; this one only catches a badly brittle bar.

180° round a pipe
Bend test on an offcut A short bar bent 180 degrees round a pipe about five times its thickness. The outside of the bend is smooth: pass. A bend with cracks across the ribs: fail. outside of bend look here for cracks Bend an offcut back on itself round a pipe ≈ 5 × the bar size Smooth: pass Cracks: fail
Schematic. Former size: IS 1786 bend test (larger formers for higher grades); a 5× pipe is the safe choice for Fe 500 to 550 bars.
At our counter

Bring a piece of any bar. We'll weigh it and read it with you.

Bought elsewhere, or not sure what the truck brought? Bring a piece to our Rewa Road store. We put it on the scale, read the marks and tell you what we see.

What we sell, and how

  • Tata Tiscon 550SD and Saluja Gold, 6, 8, 10, 12 and 16 mm. Other sizes and brands we can order for you; ask on WhatsApp for the time it takes.
  • Sold by weight, so what is weighed is what you pay for. GST bill on every sale with brand, size and kilograms.
  • Cutting and delivery are charged separately; ask for the amount for your site. See delivery and transport.
We sell genuine Tata Tiscon and Saluja Gold with a GST bill. Don't take our word for it: the marks, the app and the scale on this page work on our bars too.

Before the bars go into your slab

Questions people ask us

Short answers

Is a bar without the ISI mark fake?

For 8 mm and thicker TMT bars, a bar with no ISI mark on its tag and no maker's marks on the steel should not be bought, whatever it costs. The Ministry of Steel's Quality Control Order makes BIS certification to IS 1786 compulsory for these bars. Bars under 8 mm are left out of that order, so for 6 mm rings go by the brand mark, the weight and the bill.

Where do I find the CM/L number?

On the bundle tag, next to the ISI mark, and on the maker's test certificate. It is the maker's BIS licence number. Type it into the free BIS Care app under Verify Licence Details: the name that comes up must be the maker named on the bar.

What is the six-digit number rolled on the bar?

BIS asks makers to roll the brand, the grade and a six-digit number onto the bar at least every 3 metres. The first two digits stand for the BIS office that looks after the licence; the last four are the last four digits of the licence number. So the bar's last four digits should match the end of the CM/L number on the tag.

Does colour or shine tell you if sariya is good?

No. A dark bar, a bright bar or a light brown one can all be good or bad. Colour is not in any test. The marks rolled into the steel, the licence check, the weight and the bend are what tell you.

Is light rust on sariya a problem?

Light brown surface rust that rubs off is normal on bars stored in the open and does no harm. Reject bars with deep pits, flakes that peel off, or ribs eaten away.

Can you check a bar I bought from another shop?

Yes. Bring a piece of any bar to our Rewa Road counter. We will weigh it and read its marks with you, and tell you what we see.

What do I do if a bar fails these checks?

Stop the unloading, take photos of the bar marks, the tag and the bill, and go back to the seller. If the ISI mark or licence looks misused, complain in the BIS Care app under Misuse of ISI Mark. For Tata Tiscon you can also call Tata's toll-free line, 1800-108-8282.

Abhishek Ranjan
Diploma Civil Engineer, Tashya Ventures

Handles cement and steel at our Reva Road store, Muzaffarpur. The marking rule, licence check and weight limits on this page were checked on 13 Nov 2026 against the BIS documents and IS 1786 figures listed below. Where makers say more than the code, the page names the maker.

Where the rules come from

  1. Bureau of Indian Standards, Product manual for IS 1786 (PM/IS 1786/2, May 2019): brand, grade and six-digit identification number marked on the bar at intervals of not more than 3 m; the six digits are a two-digit branch code and the last four digits of the licence; each consignment with a test certificate carrying the Standard Mark, cast/lot number, grade, size and results.
  2. Bureau of Indian Standards, BIS Care app: Verify Licence Details by CM/L number; complaints with evidence.
  3. Ministry of Steel, Steel and Steel Products (Quality Control) Order: IS 1786 bars and wires under compulsory BIS certification, sizes below 8 mm excluded (as summarised by EVTL India).
  4. IS 1786:2008, Table 2: mass tolerance, single sample −8% (up to 10 mm), −6% (over 10 to 16 mm); standard weight d²/162. Same figures as our weight per metre page.
  5. Tata Steel, Tata Tiscon 550SD page and brochure: embossed brand and grade, Tag of Trust, toll-free 1800-108-8282.
  6. Saluja Steel & Power, Saluja Gold leaflet (Nov 2024): licence CM/L-5801867.
  7. Kamdhenu, How to identify high-quality TMT bars: light surface rust acceptable, deep pits and flaking not; bend an offcut.

Not sure about a bar?

Send us a photo of the marks and the tag on WhatsApp, or bring a piece to the store.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com