हिंदी Call90310 74624
Home›Guides›Sanitary and pipes
Plumber's words · taps

Types of taps in a house, and the point each one needs in the wall

The short answer

A plumber names about ten taps, but the wall only has to be ready in three ways. Almost every tap ends in a ½″ threaded point at the tile face. Taps that stand on a basin or counter need an angle valve on that point. A concealed stop cock or diverter needs its body set inside the wall. Choose the tap for each place now, count the points, and have them fixed before plaster. The tap itself can come after the tiles.

½″
The thread on nearly every tap15 mm BSP, so the wall point is a ½″ brass-insert elbow.
150 mm
Between a wall mixer's two pointsHot and cold, level, centre to centre (Jaquar's sheets).
0 mm
In or out from the tileThe elbow's mouth sits flush with the finished tile face.
One bathroom wall, before the taps
Bathroom wall showing where the tap points go A tiled wall with pipes drawn in. Red dots mark half-inch brass-insert elbows at the tile face for the wall mixer, the bucket tap, the cistern valve and the basin valve. A square marks the concealed stop cock body near the door. 150 mm basin, later Stop cock body Wall mixer: cold · hot Bucket tapif wanted 2-in-1 for cistern and health faucet Basin valve ½″ brass-insert elbow, flush with the tile Concealed body, set to its guard cold hot
Not to scale. A common layout for a western-WC bathroom with a geyser; your positions follow your naksha. Heights for each point are on fixture heights.
What the wall has to be ready for

Ten taps, three kinds of point

You can change your mind about the tap's look up to the day it is fitted. You can't change the kind of point without breaking tiles. So decide the kind of tap for each place before the plumber starts.

1½″ elbow at the tile face

A UPVC or CPVC elbow with a brass thread inside, its mouth flush with the finished tile. Bib cocks, long body taps, sink cocks, wall mixers and shower arms screw straight into it. So does an angle valve.

2An angle valve on that elbow

For anything that sits on a basin, counter or cistern: pillar cock, deck sink tap, WC cistern, geyser. The valve stays on the wall; a flexible connection pipe goes up to the fitting.

3A body inside the wall

A concealed stop cock or a concealed diverter. Its brass body is fixed in the wall at the pipe stage, set to the depth marked on its plastic guard. Only the knob and plate show after tiling.

Every point is ½″ because nearly every house tap is: the inlet thread is ½″ (15 mm) BSP, as on the pillar taps described by Studio Matrx and the wall mixers on Jaquar's sheets. Which pipe size feeds the point is on pipe size, tank to bathroom.

The ten taps a plumber names

Each tap, where it goes, and what it screws into

Drawn from the side, with the wall on the left. The yellow ring is the brass thread of the elbow at the tile face.

Inlet: horizontal, ½″Spout: points downGoes: bucket, washingarea, outside wall

1 · Bib cock (bib tap, short body)

The plain wall tap. Its inlet runs straight into the wall and the water falls down. It fills the bucket in the bathroom, serves the washing area and the outside wall.

Wall point: one ½″ elbow

Set it high enough for a bucket to go under. Heights: fixture heights.

Two outlets, twohandles, one inletSide outlet: hose to ahealth faucet or thewashing machine

2 · Two-way bib cock

A bib cock with a second outlet underneath, on its own handle. The spout fills the bucket; the side outlet takes a hose. Useful where you want a health faucet or washing machine hose without a second point.

Wall point: one ½″ elbow
Long spoutreaches themiddle of thebasin or sink

3 · Long body bib cock

The same wall tap with a longer spout, so the water lands in the middle of a basin or sink and not on its back edge. Used over a basin that has no tap hole, or over a kitchen sink.

Wall point: one ½″ elbow, above the basin

The point goes higher than for a pillar cock, because the tap is on the wall, not on the basin.

Stands onthe basinconnection pipefrom the angle valve

4 · Pillar cock (pillar tap)

The basin tap. It stands in the basin's tap hole and its inlet points down. A flexible connection pipe joins it to an angle valve on the wall below. The usual tap for a wash basin with a hole.

Wall point: one ½″ elbow + angle valve, below the basin

A pillar sink cock is the same idea on a kitchen counter.

Not a tap to fill from:a shut-off for one fittingUnder: basin, cistern,kitchen sink, geyser,RO purifier

5 · Angle valve (angle cock, stop valve)

Water goes in from the wall and turns 90° up into the connection pipe. You don't draw water from it; you close it to work on one fitting while the rest of the house keeps its water. One for each basin, cistern, kitchen deck tap and geyser inlet.

Wall point: one ½″ elbow

Its connection pipe and the valve are on angle valve and connection pipe.

to the cisternhealth faucetOne point, two jobs,two handles

6 · 2-in-1 angle valve

An angle valve with a second outlet on its own handle. One outlet feeds the WC cistern through the connection pipe; the other takes the health faucet hose. The usual choice beside a western WC.

Wall point: one ½″ elbow, beside the WC

Which side of the WC the cistern inlet is on is in the WC's own drawing: check before the point goes in.

Swivel spoutturns over adouble sinkcounter

7 · Sink cock (wall-mounted)

The kitchen tap that comes out of the wall above the counter, with a tall spout that swings from side to side. The counter stays clear and there is nothing under it to leak.

Wall point: one ½″ elbow, above the counter

Kitchen pipe runs and the RO point: kitchen plumbing layout.

On the countervalve and pipeunder the counter

8 · Pillar sink cock or sink mixer (on the counter)

The kitchen tap that stands in a hole in the counter or sink. A sink mixer is the hot-and-cold version with one lever. Each inlet needs its own angle valve under the counter.

Wall point: ½″ elbow + angle valve, under the counter (two for a mixer)

Hot water in the kitchen means a CPVC line from a geyser: geyser line pipe.

150 mm, level bend pipe tothe showercoldhot

9 · Wall mixer

Hot and cold come in through two crank legs and leave through one spout, set by two handles or one lever. Most come with a provision for an overhead shower: a bend pipe goes up the wall from the mixer to the shower arm, so the shower needs no point of its own.

Wall points: two ½″ elbows, 150 mm apart, level

Hot on the left, cold on the right is the usual layout; check your mixer. A mixer needs a hot line, so the geyser is decided first.

Body in the wallat the pipe stage;guard (dashed) marksthe tile faceKnob and plate aftertiles, same brand

10 · Concealed stop cock (and concealed diverter)

A valve hidden in the wall that shuts one bathroom. Its body goes in with the pipes; the knob and plate go on after the tiles. A concealed diverter is the bigger cousin: one body feeds a spout and a shower, each from its own ½″ point.

Wall point: the body itself, set to its guard

We keep the Jaquar ALD-069FT body for 15 mm lines. Buying it in two halves: bathroom fitting checklist.

The health faucet is not on the list as its own point because it hangs on a hose from a 2-in-1 angle valve or a two-way bib cock. A shower on an exposed wall mixer comes up the bend pipe. With a concealed diverter, the shower arm screws into its own ½″ elbow high on the wall.

Room by room

Which tap goes where, and its point

The usual choices on houses around Muzaffarpur, with what each one needs in the wall. Pick one per place before the plumber starts.

PlaceUsual tapPoint in the wallOr instead
Bathing, with geyserWall mixer with shower provision2 elbows, 150 mm apart (hot CPVC)Concealed diverter: body + 2 elbows
Bathing, no geyserBib cock for the bucket1 elbowTwo-way bib with a hand shower
Western WC2-in-1 angle valve + health faucet1 elbow beside the WCAngle valve + separate bib for a mug
Orissa panBib cock beside the pan1 elbowAngle valve, if a cistern is fitted
Wash basin with a holePillar cock1 elbow + angle valve under the basinBasin mixer: 2 elbows + 2 valves
Basin without a holeLong body bib cock1 elbow above the basinWall-mounted basin mixer: 2 elbows
Kitchen sinkWall sink cock1 elbow above the counterPillar sink cock: elbow + valve below
RO purifier—1 elbow + angle valve near its socketTee off the sink line (usual practice)
Washing machineBib cock with hose nozzle1 elbow above the machineTwo-way bib by the washing area
GeyserAngle valve on the cold inlet2 CPVC elbows: in and outSee geyser line
Outside, terrace, gardenBib cock (hose bib)1 elbow each—

Brass or PTMT plastic for each tap is a separate choice: PTMT vs brass taps. The full list for one bathroom, in buying order, is on the bathroom fitting checklist; which tap to buy for each place is on the bathroom tap list.

Before the walls close

Count your tap points

Choose the tap for each place. The counter adds up the elbows that go in the wall now and the valves and taps that come after the tiles.

Bathrooms
Kitchen and outside

Your points

In the wall now · from our shelf

Prices are from our latest bill and change often. Please confirm today's rate on WhatsApp or call before buying.

½″ FT elbow, brass insert, UPVC
—Cold points. Pivot Easyfit Sch 80, 15 mm (MI).Ask today's rate each
½″ CPVC elbow, brass insert—Hot points: mixer hot side, geyser in and out. We order these.Ask today's rate each
Jaquar concealed stop cock body—ALD-069FT, 15 mm. Knob kit after tiles, ordered.Ask today's rate each
Teflon tape—About one 4 m roll per five threaded points (our estimate).Ask today's rate per roll
After the tiles · we order these
Material totalAsk rate
Send this list on WhatsApp

Counts follow the point rules on this page and usual practice; your plumber may add a point. Pipes, tees and bends for the runs are separate: pipe size, tank to bathroom. Cutting and delivery are charged separately; ask for the amount for your site.

Fixed before plaster, seen after tiles

Four ways a tap point goes wrong

Each one is a few minutes to set right before plaster, and a broken tile after.

Elbow 20 mm behindthe tile face, so anextension nipple bridgesit: one more joint in the wall

Sunk behind the tile

Seen: the tap thread doesn't reach

The plumber set the elbow at the brick or the plaster, not the tile. Set the mouth where the finished tile will be: on a tiled wall that is usually about 25 mm in front of the brick (usual practice; ask your mason).

gap Elbow sticks out:the wall plate stands offthe tile, the tap sits crooked

Standing out past the tile

Seen: a gap behind the plate, a tap that won't sit straight

The other way round. A plate can't hide more than a few millimetres. Hold a straight edge across the tile line before plastering.

175 mm and 16 mm out of level cranks can'treach; mixerhangs crooked

Wall mixer points out of line

Seen: the mixer won't fit, or sits tilted

The crank legs take up only a small error. Fix both elbows on one straight piece of wood, 150 mm centre to centre and level, until the plaster sets.

Plastic thread, brass tap:tightened hard, the plasticsplits inside the wallUse the elbow with a brass insert

Plastic thread at a tap point

Seen: a damp patch round the tap months later

A plain plastic FTA is for pipe-to-pipe joints. Where a brass tap or valve screws in, use the elbow with a brass insert (MI), and on hot points the CPVC one. Thread with Teflon tape only.

Pressure-test every point with plugs in before plaster, and again before tiles: plumbing stage checklist. If a joint weeps later: leaking pipe joint.

Questions people ask us

Short answers

Bib cock or pillar cock: what's the difference?

A bib cock comes out of the wall: its inlet is horizontal and it screws straight into a ½″ point in the wall. A pillar cock stands on the basin or counter: its inlet points down through the hole, and a connection pipe joins it to an angle valve on the wall below.

What is an angle cock for? (angle cock kya hota hai)

It is a shut-off, not a tap you fill a bucket from. It sits on the wall under a basin, cistern, sink or geyser, and the connection pipe runs from it to the fitting. Close it to change a washer or a cistern part without shutting the whole house.

What is a 2-in-1 angle valve?

An angle valve with a second outlet and its own handle. One outlet feeds the WC cistern, the other takes the health faucet hose. One wall point serves both.

What thread size do taps have?

Nearly every tap, angle valve and wall mixer sold for Indian houses has a ½″ (15 mm) BSP inlet. So the wall point is a ½″ female thread: a brass-insert FT elbow, flush with the finished tile.

Long body or short body bib cock?

Short body for a bucket, a washing area or outside. Long body when the tap comes out of the wall over a basin or sink, so the water lands in the middle of the bowl.

Can I fit a wall mixer later on a single bucket-tap point?

Not without breaking tiles. A mixer needs two points, 150 mm apart, and a hot line from the geyser. If a geyser might come later, have both points and the CPVC hot line put in now and cap the hot one.

How many tap points does a 2-bathroom house need?

With wall mixers, western WCs, pillar-cock basins, a geyser in each bathroom, a wall sink cock, an RO point, one washing machine and two outside taps, it comes to 17 elbows (11 UPVC for cold, 6 CPVC for hot) and 2 concealed stop cock bodies. Use the counter above for your own choice.

Do you sell taps?

On the shelf we keep what goes into the wall: ½″ brass-insert FT elbows, MTA and FTA adaptors, reducing tees, Teflon tape and the Jaquar concealed stop cock body. Taps, mixers, angle valves, connection pipes and health faucets we order for you in the brand you choose; ask on WhatsApp for the time it takes.

Arun Tiwari
Thekedar · site work, costs and plumbing, Tashya Ventures

Twenty years on sites around Muzaffarpur. The names of the taps and the points they need are what plumbers here use; thread sizes and the mixer spacing are from the makers' sheets listed below. Where a figure is usual practice, the page says so.

Where the facts come from

  1. Studio Matrx, Pillar taps in India (Oct 2026): pillar tap inlet ½″ (15 mm) BSP, connection pipe from an angle valve, IS 8931 for copper-alloy pillar taps.
  2. Jaquar wall-mixer product data sheets and technical catalogue (technical catalogue): 150 ± 1 mm between the two inlets, ½″ BSP connections. Jaquar's site blocks automated reading; figures taken from the sheets as indexed by search.
  3. Jaquar, ALD-069FT data sheet (Jaquar Nepal): concealed stop cock body for 15 mm pipe line, 0.5–5 bar.
  4. Bureau of Indian Standards, IS 9763:2000: plastic bib taps, pillar taps, angle valves and stop valves for hot and cold water. Brass bib taps and stop valves: IS 781.
  5. Prince, CPVC and UPVC temperature ratings (82 °C and 60 °C), as on our pipe comparison: why hot points are CPVC.
  6. Our stock list: Pivot Easyfit F T elbow Sch 80 (MI) 15 mm, MTA/FTA Sch 80, reducing tee 25 × 15, Teflon tape 4 m, Jaquar ALD-CHR-069FT.
  7. Usual practice on local sites: elbow mouth at the finished tile, about 25 mm in front of brick on a tiled wall (as on our before-plaster checklist); hot left, cold right; one Teflon roll per about five points.

Send us your tap list

Tell us the taps for each place. We'll send back the points, the fittings for the wall and today's price on WhatsApp.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com