
1x1 floor tiles (300×300): the bathroom floor size, and the four ceramic designs we stock
A 1x1 tile is 300×300 mm, about one foot square. It is the size most bathroom floors use, because the many joints give grip and the small pieces follow the fall to the drain. Take it in matt for the shower area. These four are ceramic, made for bathrooms, balconies and wash areas. For a hall or bedroom floor, use a 2x2 or 2x4 vitrified tile.
- 1Matt or anti-skid tiles in the wet shower corner
- 2Plain 300×300 tiles on the rest of the floor, in the same design
- 3Drain at the lowest point; the whole floor falls gently to it
- 4Wall tiles start at the floor line, normally the matching 300×450
Why almost every bathroom floor is 1x1
Three reasons that are about the floor, not about the look.
1More joints, more grip
Every joint is a small groove that a wet foot can catch. A 300×300 tile has about four times as many joints per square foot as a 600×600. Joints only grip if they are kept even and filled, so the grout matters too: see grout gap.
2It follows the slope
A bathroom floor must fall to the drain. Small pieces can follow a fall that bends towards a drain in the corner, with little cutting. A big tile would have to be cut along the diagonals or left hollow underneath. For the shower itself, mosaic sheets follow the fall even better; 300×300 is the right size for the rest of the floor.
3It matches the wall
Wall tiles in the same series are 300×450, so floor and wall come from one set and the colours agree. All four designs below have a floor piece and wall pieces.
Honest limit: a small tile is not a waterproof floor. The water-proofing and the fall in the base are what keep a bathroom dry; the tile only finishes it. See the laying notes below.
Matt or glossy on a wet floor
Soap and water make a glossy tile slippery. Choose the finish by where on the floor it goes.
| Area | Finish | Why |
|---|---|---|
| Shower and wash corner | Matt or anti-skid | Always wet, with soap. This is where people slip. |
| Rest of the bathroom floor | Matt best; glossy only if it stays dry | Splashes reach everywhere. Matt costs you nothing in looks. |
| Balcony or utility wash area | Matt | Rain and wash water. Where rain falls straight on it, use the 400×400 outdoor anti-skid. |
| Bathroom walls | Glossy is fine | Nobody walks on a wall. |
Slip rating: the R9, R10 and R11 figure on a box is explained in our slip-rating guide. We have not found a published slip rating for these four tiles, so we do not quote one. Judge by the surface: wet your hand and feel it. A matt tile feels dry and slightly gritty; a glossy one is smooth.
The four 300×300 floor designs
All are Birla Pivot ceramic. We sell genuine Birla Pivot with a GST bill. Rates are per box; today's figure is on the rates page.


Ceramic, not vitrified: what that means for where you use it
These floor tiles are ceramic. Ceramic is fine for bathrooms, balconies and wash areas, which see water but not heavy loads. For a hall, passage or bedroom floor that people walk on with shoes all day, go for a vitrified tile: 2x2 (600×600) or 2x4 (600×1200). The difference between the two is on vitrified vs ceramic.
How many boxes for a bathroom
One box is 8 tiles and 7.75 sq ft (Birla Pivot catalogue). Boxes are sold whole, so round up.
Boxes for your bathroom
Extra for cuts is our site rule of thumb. Keep one spare box from the same batch for later repairs. The full tile, adhesive and grout list is in the tile calculator.
Pick the floor and the wall from one series
Same series number means the colours were made to agree. The wall tile is 300×450: 6 tiles and 8.72 sq ft a box.
| Series | 300×300 floor | Matching 300×450 wall |
|---|---|---|
| 393 | 393 floor matt | 393 LT · 393 HL-1 · 393 DK |
| Satvariyo-08 | Satvariyo-08 floor | LT · HL-5 |
| 1145 | 1145 floor | 1145 LT · 1145 DK |
| 1217 | 1217 floor | 1217 LT · HL-1 · HL-2 · 1217 DK |
LT is the light wall tile, DK the dark, HL the decorative highlight band. See all on 300×450 wall tiles and bathroom floor tiles.
How a bathroom floor is built under the tile
The tile is the last layer. Below it, from the slab up:
- 1Floor tile 300×300, even joints
- 2Tile adhesive, Birla White TileStix, on a clean cured bed
- 3Hi-Flex coat, UltraTech Weather Pro Hi-Flex, under the tile
- 4Screed with Seal & Dry SBR in the base coat, cut to the fall
- 5Concrete slab
- Fix the fall first. Make the slope to the drain in the base coat, not in the tile bed, so every tile can sit flat on a straight line.
- Waterproof the bed and take it up the walls before any tile goes down. Let the wall and floor dry; test by touch and colour.
- Use tile adhesive on a clean, cured bed. The TileStix we stock is for ceramic tiles up to 450×450 mm indoors, so it suits these tiles; it is not for our big vitrified tiles.
- Start from the drain side and work to the door, so the cut tiles end up at the door.
- Keep joints even. The joint is the grip. Fill with tile grout and let it cure before the first shower.
Short answers
Which tile is best for a bathroom floor?
A matt 300×300 ceramic. Of our four, 393 floor matt is the one the bill marks matt, and Satvariyo-08 is listed matt too. Use the same finish through the shower area.
Matt or glossy tiles for a bathroom floor?
Matt or anti-skid wherever the floor gets wet, which in a bathroom is almost everywhere. Glossy belongs on the walls, where nobody walks.
Why are 1x1 tiles used in bathrooms?
The many joints give grip, the small pieces follow the fall to the drain, and the size matches the 300×450 wall series so floor and wall come from one set.
How many tiles are in a 300×300 box?
8 tiles, 7.75 sq ft, from the Birla Pivot catalogue. One tile is about 0.97 sq ft, a little under a square foot.
Can I use ceramic 1x1 tiles in a hall?
They are made for bathrooms, balconies and wash areas, not for a hall that sees shoes and furniture all day. For halls take 2x2 or 2x4 vitrified tile.
How do I match floor and wall tiles?
Take both from one series number, for example 1145 or 1217, then check the pair on the table above. Each series has a 300×300 floor piece and 300×450 wall pieces.
Paint Engineer at our Reva Road store, Muzaffarpur, and the person who advises on tiles. Box figures on this page come from the Birla Pivot tile catalogue. Where a figure is not published, the page says so instead of guessing.
Where the numbers come from
- Birla Pivot, tiles catalogue and birlapivot.com product pages: 300×300 floor box of 8 tiles, 7.75 sq ft; 300×450 wall box of 6 tiles, 8.72 sq ft; Satvariyo-08 and 393 floor product codes marked MT (matt).
- Our own bills: 393 floor billed as "FloorMatt"; 1145 and 1217 floor finish is not on the bill.
- Birla White TileStix Intero Grip+ (TX2): ceramic tiles up to 450×450 mm, indoors only (maker's product page).
- Not used for any figure: retailers' guides to bathroom tiles. They agree on matt over glossy and on small tiles for grip and slope; the numbers above are ours or the maker's.
Send us your bathroom size
We will tell you how many boxes, which design and the wall tile to match, with today's price.