हिंदी Call90310 74624
Home›Waterproofing›Roof, while casting
Waterproofing · product

UltraTech Weather Pro Hi-Flex in Muzaffarpur: the roof and bathroom coating, 14–15 sq ft per kg, 12 and 24 kg

The short answer
  1. Clean, dry, cracks filled
  2. Coat 1
  3. 8 hours or more
  4. Coat 2, crosswise
  5. Screed on top

Hi-Flex is a two-part coating, powder and liquid mixed on site, that dries into a rubbery skin which stretches up to 100% and holds water pressure up to 7 bar. 1 kg of mix covers 14–15 sq ft for one coat, and a roof needs two coats. So a 1000 sq ft roof takes about 134–143 kg, which is six 24 kg packs. Some sites quote about 70 kg: that is one coat only.

134–143 kg
Hi-Flex for 1000 sq ft, two coatsFlat roof only. With 1 ft up the parapet it is about 162 kg.
8 hours
Between coat 1 and coat 2The second coat goes at right angles to the first.
12 · 24 kg
Packs we stockPowder and liquid come together in the pack.
Two coats, laid crosswise, under a screed
Layers of a Hi-Flex roof, and the two coats laid crosswise A cross-section shows, from the bottom, the concrete slab, a first coat of Hi-Flex, a second coat of Hi-Flex and a screed on top; the coats are drawn thicker than the real 0.6 to 0.7 mm so they can be seen. Below it, two squares show the first coat brushed in one direction and the second coat, at least 8 hours later, brushed at right angles to it. Screed (UltraTech: highly recommended) Coat 2 · 0.6–0.7 mm Coat 1 · 0.6–0.7 mm Roof slab, cured and dry Coats drawn thicker than real so you can see them COAT 1COAT 2, 8 H OR MORE LATER one way at right angles 1 kg of mix = 14–15 sq ft per coat
Not to scale. UltraTech: two coats of 0.6–0.7 mm, at least 8 hours apart, the second at right angles, and "highly recommended" a layer of screed or plaster over the coating.
Where it goes

On the side the water falls on

UltraTech lists Hi-Flex for "positive side" jobs: the face that gets the rain or the splash. It is a coating over a surface, not a cure for damp that comes up inside the wall.

1Yes

Listed by UltraTech
  • Roofs and terraces, flat or sloping
  • Balconies and domes
  • Outside walls
  • Bathroom, kitchen and sunken floors and walls

New roof? The full plan is on waterproofing while casting. Bathroom? Bathroom waterproofing.

2With a screed on top

UltraTech: "highly recommended"
  • Any roof people walk on
  • Roofs with pots, tank or solar stand
  • Under tiles: the tile bed is the screed

The coat is a thin skin of 0.6–0.7 mm a layer. The screed keeps feet, sun and tools off it.

3Ask us first

Not in UltraTech's list
  • Inside a drinking-water tank: not Hi-Flex; use Weather Pro Single Component (CFTRI food-grade approved), which we order. Hi-Flex is for the tank's top and outside
  • Damp rising from the ground, showing on the inner face: Seep Blocker 2K
  • A wall that is wet inside: let the leak be fixed and the wall dry first

Not sure? Send a photo of the leak. We tell you the product, not the dearest one.

How it is laid

Prepare, two coats, a screed

Where the roof meets the parapet
Hi-Flex at the parapet foot, taken up the wall A parapet wall stands on a concrete slab. A rounded mortar gola fills the corner where they meet. Two coats of Hi-Flex run across the slab, round the gola and about one foot up the parapet. A screed covers the coating on the slab. Hi-Flex up the wall about 1 ft screed slab parapet gola (rounded corner)
Round the corner with a gola so the coat does not bend sharply, and carry it about a foot up the wall. The gola and the foot of coating are usual practice, the same as on the new-roof page.
StepWhat to do
1. Surfaceafter UltraTech's "surface preparation"Clean and dry. Sweep, wash off dust and loose mortar, fill cracks with SBR mortar (Seal & Dry), round the corner with a gola. Follow the pack for any primer.
2. MixMix the powder and the liquid, both in the pack. UltraTech's brochure does not print the ratio or the working time, so take them from the pack, and mix only what you can lay at once.
3. Coat 1Brush or roller, about 0.6–0.7 mm. Over the roof, round the gola and about a foot up the parapet. 1 kg of mix does 14–15 sq ft.
4. WaitUltraTech8 h or more
5. Coat 2Same thickness, laid at right angles to coat 1. If coat 1 was along the roof, coat 2 goes across.
6. ScreedA layer of screed or plaster over the coating (UltraTech: highly recommended). 1:4 cement-sand with WP+200 is our usual mix.
Dry weather onlyUltraTech gives no rain or temperature limit for Hi-Flex. We do not lay it when rain is coming, and we do not start the second coat on a wet first one. In Muzaffarpur that means April to early June, or a dry spell after the monsoon.
Kilos for your roof

Area × 2 coats ÷ 14 or 15

The brochure's 14–15 sq ft per kg is for one coat, and a roof gets two. So kilos = area × 2 ÷ 15 at the low end and area × 2 ÷ 14 at the high end. Packs are picked for the high figure.

Bathroom? Floor plus wall strip is the area. A 1000 sq ft roof with 126 ft of parapet is about 162 kg.

Your Hi-Flex

Total area to coat—

Prices are from our latest bill and change often. Please confirm today's rate on WhatsApp or call before buying.

UltraTech Weather Pro Hi-Flex
—1 kg covers 14–15 sq ft per coat (UltraTech)
Packs to buy——Ask today's rate per kg
Material totalAsk rate
Send this to Tashya

Prices fill in from today's rate. Full roof list with cement and WP+200: new roof. Walls, tanks and more: waterproofing calculator.

Flat areaTwo coatsPacks
500 sq ft67–72 kg3 × 24 kg
1000 sq ft134–143 kg6 × 24 kg
1500 sq ft200–215 kg9 × 24 kg
2000 sq ft267–286 kg12 × 24 kg

For more, see how much Hi-Flex. A rough or porous surface can take more than the brochure figure; a 12 kg pack of spare is cheaper than a roof stopped halfway.

Hi-Flex or something else

Three coatings, one rule of thumb

Hi-FlexFlex
Stretches up to100%50%
1 kg covers, per coat14–15 sq ft12–14 sq ft
Packs12 kg, 24 kg3 kg, 15 kg, 30 kg
With usOn the shelfWe order it for you; ask on WhatsApp for the time

UltraTech's figures for both, tested as per ASTM D 412 on a 1 mm film. Hi-Flex stretches further and covers more per kg, so it is the one for roofs where heat opens cracks every summer.

Our other two-part coating is Birla White Seep Blocker 2K, in smaller packs and also used on the inner face of a wall. Hi-Flex vs Seep Blocker 2K sets them side by side. Terrace with an old leak: terrace waterproofing.

What goes wrong

Three ways a Hi-Flex roof still leaks

1 coat2 coats67–71 kg134–143 kghalf the job

Bought for one coat

Shows up as: thin film, pinholes, a leak by the second monsoon

The 14–15 sq ft per kg is one coat. A 1000 sq ft roof needs 134–143 kg, not 70. Count two coats before you pay.

water gets inpinholes line up

Both coats the same way

Shows up as: leaks at the same few spots

Pinholes from brushing in one direction line up in both coats. Lay coat 2 at right angles, as UltraTech says, and wait the full 8 hours.

Left bare:feet and sun wear it thin

Left bare

Shows up as: worn patches by the stairs and tank

The coat is 0.6–0.7 mm a layer. UltraTech highly recommends a screed or plaster over it, so give it one before the family walks on the roof.

Questions people ask us

Short answers

How many kg of Hi-Flex for a 1000 sq ft roof?

About 134–143 kg of mix. UltraTech says 1 kg covers 14–15 sq ft, and the brochure's coat is one of two, so 2 × 1000 ÷ 15 = 133 kg to 2 × 1000 ÷ 14 = 143 kg. Six 24 kg packs (144 kg) cover it. If the coat also climbs 1 ft up the parapet, add that strip: about 162 kg for a 1000 sq ft roof, as on the new-roof page.

Some sites say about 70 kg for 1000 sq ft. Which is right?

70 kg is one coat: 1000 ÷ 14.5. UltraTech's method is two coats of 0.6–0.7 mm, at least 8 hours apart, and a kilo of mix cannot cover 14 sq ft with two coats that thick, so the 14–15 figure is for one coat. Buy for two.

Can I give just one coat to save money?

No. One coat gives half the thickness UltraTech asks for, and any pinhole in it goes straight through. The second coat, laid at right angles, closes the pinholes of the first. The saving is small next to a second roof job.

Do I have to put a screed over Hi-Flex?

UltraTech calls a layer of screed or plaster over the coating "highly recommended". On a roof where people walk, dry the pots, or put a water tank, we always do it. The screed protects the coat from feet, sun and tools.

12 kg or 24 kg pack?

Count the kilos first, then pick packs that cover the higher figure. 24 kg covers about 168–180 sq ft with two coats; 12 kg covers 84–90 sq ft. A bathroom of 50–80 sq ft with the wall strip is usually one 12 kg pack; a roof is 24 kg packs.

Can Hi-Flex stop damp coming from inside the wall?

No. UltraTech lists Hi-Flex for "positive side" use: the face the water falls on, such as roofs, terraces, balconies, outside walls and bathroom floors. For damp rising from the ground and showing on the inner face of a wall, Birla White Seep Blocker 2K is the right product; compare the two on Hi-Flex vs Seep Blocker 2K.

Is Hi-Flex for water tanks?

Hi-Flex is for a tank's top and outside. Inside a drinking-water tank use UltraTech Weather Pro Single Component, which UltraTech's brochure lists as food-grade approved by CFTRI; we order it for you. Hi-Flex's listed uses are roofs, terraces, sloping roofs, walls, balconies, domes, bathrooms, kitchens and sunken floors.

Is the price fixed?

Prices on this site show "Ask rate" until the day's rate is filled in. Send us your roof size on WhatsApp and we send back the kilos, packs and today's price.

Mr Mustafaa
Paint Engineer, Tashya Ventures

Paint and waterproofing at our Reva Road store, Muzaffarpur. Every number on this page was checked against UltraTech's brochure on 13 Nov 2026. What the brochure does not say, the page says too.

Where the numbers come from

  1. UltraTech, Weather Pro waterproofing brochure (Flex, Hi-Flex & Single Component page): polymer-based coating; elongation up to 50% (Flex) and 100% (Hi-Flex), tested as per ASTM D 412 at 1 mm; water pressure up to 7 bar; positive-side uses; 0.6–0.7 mm per coat; 1 kg of mix covers 14–15 sq ft (Hi-Flex) and 12–14 sq ft (Flex); two coats with at least 8 hours between, the second at right angles; screed or plaster over it "highly recommended"; packs Hi-Flex 12, 24 kg and Flex 3, 15, 30 kg. The brochure gives no mixing ratio, working time, warranty or rain limit.
  2. Coverage per coat: a kilo of mix cannot cover 14 sq ft in two coats of 0.6–0.7 mm, so the 14–15 sq ft is counted per coat and doubled for two coats. This is how our owner and the chhat dhalai and bathroom pages count it.
  3. Asian Paints, "How to apply terrace waterproof coating" and "Waterproof coating for roof and terrace", and Dr. Fixit's roof waterproofing FAQ, read for what a reader is told elsewhere: all three give the steps but no coverage per kg, no drying gaps and no quantity for a roof.
  4. Gola, one foot of coating up the parapet, 1:4 screed with WP+200, dry-weather rule: usual practice, not a maker's figure.

Send us your roof or bathroom size

We send back the kilos of Hi-Flex, the packs and today's price on WhatsApp. A photo of the leak helps us pick the right product.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com