हिंदी Call90310 74624
Home›Waterproofing›Waterproofing products
Waterproofing product · UltraTech

UltraTech Seal & Dry SBR: what it does, how it is mixed, and where it will not help

The short answer
  1. SBR latex
  2. + cement (+ sand)
  3. = bond slurry, repair mortar or waterproof coat

Seal & Dry SBR is a milky white rubber liquid. It is never used on its own. Mixed into cement it makes the mix stick to old concrete, close its pores and crack less. It is the cheap fix for a patch, a pipe sleeve, a corner or the base coat under plaster. It is not a coating that stops a leaking roof; for that, use Hi-Flex.

1 + 20 kg
Packs we sell1 kg and 20 kg. Other sizes: we can order it for you.
1 : 8
Latex to cement, by weightSika's sheet for its SBR. Ours may differ: the pack ratio rules.
20 mm
Most in one layerSika's limit for SBR mortar. Thicker goes on in layers.
The bond coat, in section
The SBR bond coat in section From the left: old concrete, a thin brushed film of SBR and cement slurry, then new mortar up to 20 mm thick put on while the slurry is sticky. up to 20 mm a layer 123 Old concreteSBR slurryNew mortar clean, rough, soakedbrushed in, thingoes on while sticky Slurry is glue only while it is wet. Put the mortar on before it dries, in 20–30 min at 30 °C (Sika).
Not to scale: the slurry is a brushed film, much thinner than drawn. 20 mm limit and 20–30 minute working time are from Sika's SikaLatex SBR sheet.
Four jobs, one liquid

What masons use SBR for

Cement mortar is strong but porous, and it grips smooth old concrete badly. The rubber particles in SBR fill the pores and make the mix stick. Every use below is the same trick.

1 · Bond coat

New plaster or screed on old concrete
Old concreteSBR slurryNew mortar
  • A thin cement-and-SBR slurry is brushed on, and the new mortar goes over it while it is still sticky.
  • Used where plaster or a screed is added to an old slab, column or beam.
Sika: about 30 g of latex per sq m, one coat.

2 · Repair mortar

Patches, broken corners, honeycombing
Chip outSBR slurrySBR mortar
  • The same SBR goes into the mortar that fills the hole, so the patch holds and does not shrink away from the edge.
  • Roof or parapet repair: WP+200 goes in this mortar too.
Sika: about 45 g of latex per sq m for each 1 mm of mortar.

3 · Waterproof coat

A thin cement-SBR layer on a sound base
Clean base2 coats of slurryPlaster over
  • Two brushed coats make a water-resistant skin on a sound slab or wall, to be covered by screed or plaster.
  • It is a rigid skin, not a stretchy one: it does not bridge cracks that keep moving.
Sika: about 70 g of latex per sq m, two coats.

4 · Bathroom

Pipe sleeves, floor trap, corner gola
SBR slurry on pipeSBR mortar packed
  • The gap round every pipe is packed solid with SBR mortar, and the rounded gola in every corner is made with it.
  • The coating over it is Hi-Flex or Seep Blocker 2K. See bathroom waterproofing.
Re-fixing one or two loose tiles with cement: SBR in the mix is usual practice. For a whole floor use tile adhesive.
Mixing

How SBR goes into the mix

The order matters more than the brand: the latex goes into the water first, and the cement goes into that.

Mixing order
Order of mixing SBROne: SBR into water. Two: add cement slowly while stirring. Three: mix for no more than two minutes and use within the working time.1SBR into the waterLatex and water togethermake the gauging solution2Cement into thatAdd part of the solution to the tub,then cement (and sand), slowly stirring2 min3Mix, then useTwo minutes at most, hand or slow drill.Use within the working time.
Order and 2-minute limit: Sika's SikaLatex SBR sheet. Thin slurry and mortar are both mixed this way.

What the makers say

UltraTech does not publish a data sheet for Seal & Dry SBR online. Its waterproofing range page lists SBR with one line, and the only listings we found are seller pages. The ratios are printed on the pack. Send us a photo of the pack on WhatsApp and we will read it with you.

Other makers' sheets show why you must follow the pack, because they do not agree:

MakerBond coatWaterproof coat
Sika SBRby weight, latex : water : cement1 : 4 : 81 : 4 : 8
Dr. Fixit Pidicrete URPratio as its blog words it, order not stated1 : 11 : 2

Sika's mix is one part of latex to eight of cement, with water; Dr. Fixit's blog gives a plain 1 : 1 and 1 : 2 with its own product. Products are diluted differently, so one maker's ratio cannot be borrowed for another's. Safe pick: the ratio on the UltraTech pack. If it is unreadable, send us the photo.

How much to buy

SBR and cement for your job

Planning figures from Sika's published consumption table, since UltraTech gives none. Low is the sheet figure, high is 25% more for a rough surface. Mix the pack as printed on the UltraTech pack, and buy to the high number.

Area: — sq m (1 sq ft = 0.0929 sq m)

Your list

UltraTech cement—Cement that goes into the mix, at Sika's 8 parts cement to 1 part latex. 50 kg bags.—
Sand—1 : 4 cement to sand by weight, as in Sika's mortar. Not sold in packs here; ask on WhatsApp for sand delivery.
Material totalAsk rate
Send this list on WhatsApp

Prices are filled in from today's rate. Cutting and delivery are charged separately; ask for the amount for your site (delivery).

Using it

Bond coat and mortar, step by step

Steps follow Sika's sheet; the working time shortens in Bihar's summer heat, so mix small batches.

  1. 1

    Clean the base

    Take off oil, paint, dust and the weak skin of cement (laitance). The UltraTech listing asks for exactly this. Chip smooth concrete to give it a key.

    same day
  2. 2

    Soak the base, then wipe it

    Wet the concrete or brick at least 2 hours before, until it is dark and damp but has no shine and no puddles. A dry base drinks the water out of the slurry.

    2 h before
  3. 3

    Mix: water and SBR first, cement into it

    Pour part of the SBR-and-water into the tub, add cement (and sand for mortar) while stirring slowly, then use the rest to set the thickness. Mix by hand or slow drill for no more than 2 minutes.

    2 min
  4. 4

    Brush the slurry in hard

    Work it into every pore with a stiff brush, one thin even film. Keep out of direct sun and strong wind.

    20–30 min working time
  5. 5

    Mortar over it while the slurry is sticky

    Not after it has dried. Put mortar up to 20 mm in one layer; for more, add further layers about 12 hours apart.

    layers 12 h apart
  6. 6

    Keep it damp

    Sprinkle water for 3 to 4 days. This is the curing Birla White asks for on its SBR bathroom gola, and it is the usual practice for any cement work.

    3–4 days damp
Pack and storageSika gives 18 months from the date of production for its sealed pack, kept dry between 5 and 35 °C, away from frost and sun. Look for the date on our pack; keep an opened one tightly shut.
What goes wrong

Four ways SBR work fails

Slurry driedno gripplaster sounds hollowand lifts at edges

Slurry left to dry

You see: new plaster hollow and lifting at the edges

The slurry is only a glue while wet. Brush a small area, plaster it, then move on.

Pure latex on baseslick filmplaster slides off(Sika: never)

Neat latex brushed on

You see: plaster sliding off a slick white film

Sika says never to put pure SBR, or SBR with water, straight on the base. Always add cement.

40 mm in one gocracks throughbuild up in layers12 h apart

One thick pass

You see: cracks running through a thick patch

Over 20 mm, build up in layers 12 hours apart, as in Sika's sheet.

Left bare in sun,no plaster over itSBR has poor UV resistance

Left as the final face

You see: a surface that breaks down in sun

Permagard's sheet notes poor UV resistance, so SBR is not for exposed coloured finishes. Cover a waterproof coat with screed or plaster, as UltraTech asks for its Hi-Flex coating.

Right product, right leak

SBR, WP+200 or a coating?

Choose by where the water comes from. SBR mortar is the helper in most of these, not the whole fix.

The problemWhat fixes itWhere SBR comes in
Bathroom leaks into the room belowbathroom pageHi-Flex under the tiles, WP+200 in the screedPipe sleeves, trap and corner gola
Roof or parapet leakterrace pageHi-Flex coating, WP+200 in the repair mortarBond coat for the patch
Damp rising from the groundSeep Blocker 2K on the inside face, waterproof puttyLittle or none
Outside wall wet in rainWP+200 in plaster, then Birla Opus exterior paintBond coat where new plaster meets old
Small cracks or jointscracks pageRake out and fillSBR mortar for the filling

WP+200 is a different product: a liquid for the whole mix, at 200 ml per 50 kg bag. See how much WP+200 per bag. For the full SBR how-to, see SBR kaise use kare.

On our shelf

Seal & Dry SBR and what goes with it

Other pack sizes, or anything else for this job: we can order it for you; ask on WhatsApp for the time it takes. Every sale has a GST bill.

Questions people ask us

Short answers

What is SBR used for?

SBR (styrene-butadiene rubber) latex is added to cement mix. It makes a bond coat between old and new concrete or plaster, a stronger repair mortar, and a thin water-resistant cement coat. It is also what masons pack round bathroom pipes.

Can SBR be used alone as a waterproof paint?

No. Sika's sheet says never to apply pure SBR, or SBR and water, directly on the base; cement must always go in. Even with cement it is a rigid skin and does not bridge a crack that keeps moving. For roofs, use a flexible coating such as Hi-Flex.

How much SBR for one bag of cement?

By Sika's ratios, 1 kg of latex goes with 8 kg of cement for slurry and mortar, so about 6 kg for a 50 kg bag. Its screed figure is 10% of the cement weight, 5 kg per bag. UltraTech's own pack may differ, and the pack rules.

Is SBR the same as WP+200?

No. WP+200 is a small dose, 200 ml per 50 kg bag, to make the concrete or plaster itself water-repellent. SBR is a large dose that improves grip and cuts cracking. In a bathroom or roof repair you often use both.

Can SBR go under paint or tiles?

It can be in the plaster or screed under them. Do not leave an SBR coat as the exposed final face. For a whole tile floor use tile adhesive.

How long does one pack keep?

Sika gives 18 months from production for its sealed pack, between 5 and 35 °C. Check the date on our pack, and keep an opened pack tightly shut.

Does Seal & Dry SBR have an official UltraTech page?

UltraTech lists SBR in its waterproofing range but has no data sheet under this name online. That is why the mix ratio is the one printed on the pack, and why this page uses Sika's published table only for planning quantities.

1 kg or 20 kg?

A bathroom or a few patches: 1 kg. Plastering a wall or screeding a roof: the 20 kg pack. At Sika's ratio, 20 kg of latex goes with about 160 kg of cement.

Mr Mustafaa
Paint Engineer, Tashya Ventures

Paint Engineer at our Reva Road store, Muzaffarpur. Where the makers disagree, this page says so and gives the safer figure.

Where the numbers come from

  1. Sika India, SikaLatex SBR product data sheet (Dec 2023, v02.01): mixing ratios 1 : 4 : 8 (latex : water : cement) and 1 : 4 : 8 : 32 for mortar, consumption, 20 mm layer limit, 12 h between layers, 2-minute mixing, 20–30 min working time, pre-wetting at least 2 h, 18-month shelf life. Used as the planning reference, since UltraTech publishes no sheet.
  2. Dr. Fixit, SBR latex in waterproofing: uses and how to apply: uses, 1 : 1 bond coat and 1 : 2 waterproof coat with Pidicrete URP, no coverage or curing given.
  3. Moglix, UltraTech 5 kg SBR Seal & Dry listing: seller page, describes waterproofing agent, binder and mortar modifier, asks for oil, dust and laitance to be removed; gives no ratios.
  4. Permagard, SBR bonding additive data sheet: poor UV resistance.
  5. Birla White Seep Blocker 2K warranty booklet and Levelplast sheet, as read for our bathroom page: SBR gola, 3–4 days damp cure.

Send us the job

Tell us where the SBR goes and the area. We will send back SBR, cement and WP+200 for it, with today's price, on WhatsApp.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com