हिंदी Call90310 74624
Home›Guides›Waterproofing
Waterproofing guide · quantity

How much Hi-Flex do I need? Roof, bathroom, sunken floor, balcony and tank, in kilos and packs

The short answer
sq ft to coat×2 coats÷14=kg to buy

UltraTech says 1 kg of Hi-Flex mix covers 14–15 sq ft for one coat, and its method is two coats. So count about 1 kg for every 7 sq ft. The square feet are more than the floor: the strip up the parapet or wall, the sides of a sunken floor and the second layer under bathroom tiles all count.

134–143
kg, 1000 sq ft flat roofSix 24 kg packs. With 1 ft up the parapet, about 162 kg: seven packs.
28–30
kg, a 6 × 8 ft bathroomBoth layers: inside the sunk and under the tiles. One 24 kg + one 12 kg pack.
70 kg?
Is one coat onlyThe figure some sites give for 1000 sq ft. Buy for two coats.
What one kilo and one pack cover
Coverage of Hi-Flex per kilo and per pack One kilo of mix covers 14 to 15 square feet with one coat, but only about 7 to 7.5 square feet with the two coats UltraTech asks for. A 24 kg pack covers 168 to 180 square feet with two coats, about a 13 by 13 foot area. A 12 kg pack covers 84 to 90 square feet, about one layer of a 6 by 8 foot bathroom floor with its 1 foot wall strip. ONE COAT 1 kg 14–15 sq ft, one coat UltraTech's figure TWO COATS · THE RIGHT WAY 1 kg 7–7.5 sq ft, two coats half the area 1 square = 1 sq ft · dashed = one coat's reach PER PACK, TWO COATS 24 kg 168–180 sq ft ≈ 13 × 13 ft 12 kg 84–90 sq ft 12 kg ≈ one layer of a 6 × 8 ft bathroom floorwith its 1 ft wall strip (76 sq ft)
Coverage and packs: UltraTech Weather Pro brochure. One-coat figure doubled for two coats, as on our Hi-Flex, roof and bathroom pages.
Measure this, not the floor

The square feet hide in the corners

Short orders happen because only the floor was measured. Here is what each job really adds up to, opened out flat. The kilos under each drawing are two coats at 14–15 sq ft per kg.

A 40 by 25 ft roof with a 1 ft strip up the parapet all round, opened out: 1000 plus 130 square feet 1000 sq ft roof inside the parapet 40 ft 25 ft 1 ft up the parapet · 130 ft long

Roof with parapet

1000 + 130 = 1130 sq ft → 151–162 kg

The parapet foot is where most roofs leak, so the coat goes over the gola and 1 ft up the wall. That strip is 1 sq ft for every foot of parapet. Full roof plan: new roof · old terrace.

A 6 by 8 ft sunken bathroom floor opened out: floor, four sunk sides 1 ft deep, and a 1 ft strip up the room walls floor 48 8 × 6 ft sunk sides, 1 ft deep · 28 1 ft up the room walls · 28 sunk layer = 104 sq ft

Sunken floor

104 sq ft → 14–15 kg (sunk layer)

Floor, the four sides of the sunk, and 1 ft up the room walls. A bathroom then gets a second layer under the tiles (106 sq ft with a 4 ft tap wall), so a 6 × 8 bathroom is 210 sq ft, 28–30 kg. Steps: bathroom waterproofing.

A 10 by 4 ft balcony opened out: floor plus a 1 ft strip up the house wall and both side walls floor 40 10 × 4 ft 1 ft up the house wall and sides · 18 open edge, railing 58 sq ft

Balcony or open floor

40 + 18 = 58 sq ft → 8–9 kg

The joint with the house wall is the weak line. One 12 kg pack does a 10 × 4 ft balcony with room to spare. A sunken kitchen or utility floor is counted like the sunken drawing.

A concrete overhead tank 6 by 5 ft and 4 ft high: the top and the four outside faces can take Hi-Flex outside top 30 6 ft × 5 ft, 4 ft high sides 88

Tank top and outside

30 + 88 = 118 sq ft → 16–17 kg

The outside of a concrete tank faces the rain like a roof or wall, which is Hi-Flex's job. The inside, where drinking water sits, is a different product: see the tank answer.

Your house, every job in one list

Hi-Flex for the whole house

Tick the jobs you are doing and put in the sizes in feet. We add them up and pick the 12 and 24 kg packs for the high figure, so one bill covers the roof, the bathrooms and the rest.

Leave out only what stays covered, like a stair cabin's floor. Old roof with cracks: terrace steps.
Wet wall = the tap wall plus about 2 ft of each side wall. Sunk depth 0 means no sunk, so only the layer under the tiles is counted. Same method as bathroom waterproofing.
Wall length = every wall the floor meets. Leave out the open edge with the railing.
The inside is not counted as Hi-Flex. It gets UltraTech Single Component, shown on its own line. Why: the tank answer.
For a wall that is wet from outside in the rain, the usual answer is WP+200 in the plaster and exterior paint; Hi-Flex suits a parapet face or a chhajja top.

Your Hi-Flex

Roof——
Bathrooms——
Balcony or floor——
Tank, outside——
Wall, parapet, chhajja——
Total, two coats—
Buy: ——
UltraTech Weather Pro Hi-FlexAsk rate1 kg covers 14–15 sq ft per coat (UltraTech), two coats. Packs picked for the high figure (÷ 14).
Seal & Dry SBR, for cracks and pipe sleeves1 kgBond slurry before the coat. More if big areas are built up.
Material totalAsk rate
Send this list on WhatsApp

Prices fill in from today's rate. Cement, balu and WP+200 for the screed over the coat: roof list · bathroom list. Cutting and delivery are charged separately; ask for the amount for your site.

Ready answers

Common roofs and bathrooms, worked out

Kilos are two coats, from area × 2 ÷ 15 (low) to area × 2 ÷ 14 (high). Packs cover the high figure.

Roof inside parapetFlat roof onlyPacksWith 1 ft up the parapetPacks
500 sq ft25 × 20 ft · 90 ft parapet67–72 kg3 × 2479–85 kg4 × 24
800 sq ft32 × 25 ft · 114 ft parapet107–115 kg5 × 24122–131 kg5 × 24 + 1 × 12
1000 sq ft40 × 25 ft · 130 ft parapet134–143 kg6 × 24151–162 kg7 × 24
1200 sq ft48 × 25 ft · 146 ft parapet160–172 kg7 × 24 + 1 × 12180–193 kg8 × 24 + 1 × 12
1500 sq ft50 × 30 ft · 160 ft parapet200–215 kg9 × 24222–238 kg10 × 24
2000 sq ft50 × 40 ft · 180 ft parapet267–286 kg12 × 24291–312 kg13 × 24
Bathroom, 1 ft sunk, bucket bathArea, both layersHi-FlexPacks
5 × 4 ftwet wall 8 ft118 sq ft16–17 kg1 × 24
7 × 5 ftwet wall 9 ft169 sq ft23–25 kg1 × 24 + 1 × 12
8 × 6 ftwet wall 10 ft210 sq ft28–30 kg1 × 24 + 1 × 12
9 × 7 ftwet wall 10 ft252 sq ft34–36 kg1 × 24 + 1 × 12
8 × 6 ft, showerwet wall to 7 ft240 sq ft32–35 kg1 × 24 + 1 × 12
8 × 6 ft, no sunkunder-tile layer only106 sq ft15–16 kg1 × 24, or 2 × 12

The 1000 sq ft row is the same figure as on the Hi-Flex page and waterproofing while casting: 134–143 kg flat, about 162 kg with the parapet strip. Bathroom areas use the bathroom page's method.

Turning kilos into packs

12 kg or 24 kg, and why we round up

Buy for the high figure

area × 2 ÷ 14
  • UltraTech gives a range, 14–15 sq ft per kg, and no extra for waste. A rough or porous slab drinks more.
  • The gap between ÷ 15 and ÷ 14 is your margin. We do not add a second "wastage" on top.
Running out on day two means a joint in the coat where the new batch meets the old.

24 kg for roofs

168–180 sq ft with two coats
  • Fewer packs to carry up and open.
  • Mix only what you can lay before it thickens. UltraTech's brochure prints no working time, so go by the pack.

12 kg for small jobs

84–90 sq ft with two coats
  • A balcony, a chhajja, one bathroom layer, or the top-up after 24 kg packs.
  • Powder and liquid come matched in the pack. Don't split a pack by eye.

Doing it in stages?

Bathroom: sunk now, tiles later
  • Count both layers now, buy the sunk layer's packs first.
  • Keep the bill: the second layer can be the same pack size weeks later.
The water tank question

Hi-Flex on the outside of a tank, not inside a drinking-water tank

UltraTech lists Hi-Flex for roofs, walls, balconies, domes and wet rooms. It makes a separate coating for drinking-water tanks, and says so in the same brochure.

Which coating goes where on an overhead concrete tank Cross-section of a concrete overhead tank on a roof. The top slab and the outside faces are marked red for Hi-Flex. The inside faces, touching the drinking water, are marked blue for UltraTech Single Component, which is food-grade approved. A plastic tank beside it needs no coating. ROOF Top and outside Hi-Flex, 2 coats rain side, like a roof Inside, in the water Single Component food-grade (CFTRI) 2 coats: 11 sq ft/kg plastic no coating
Hi-Flex uses and Single Component: UltraTech Weather Pro brochure. Coats drawn far thicker than they are.
Hi-Flex fits

The top slab and outside faces

These take the rain and sun like any roof or wall, which is "positive side" work in UltraTech's list. Count them with the tank line in the calculator: a 6 × 5 × 4 ft tank is 118 sq ft, 16–17 kg.

Not Hi-Flex

The inside of a drinking-water tank

UltraTech names a separate product for this: Weather Pro Single Component, "food-grade approved by CFTRI" in its brochure. 1 kg mixed with 350–380 ml of water covers 11 sq ft in two coats, 2–3 hours apart. Packs 1, 5 and 25 kg. We order it for you; ask on WhatsApp for the time.

Inside area = floor + four walls. A 6 × 5 × 4 ft tank is 118 sq ft, about 11 kg: two 5 kg packs and one 1 kg. Birla White also sells a food-grade tank coating, Seep Blocker Pro 2K, which we can order too. Full steps: water tank waterproofing.

Nothing needed

A plastic tank

No coating. If the roof under it leaks, it is the roof that needs Hi-Flex and a screed, with the stand on top of the screed.

What changes the kilos

Six things that make the order wrong

Halves it

Counting one coat

14–15 sq ft per kg is one coat. "70 kg for 1000 sq ft" is one coat. UltraTech's method is two, the second laid across the first.

+10–15% on a roof

Forgetting the parapet strip

1 ft up a 130 ft parapet adds 130 sq ft, about 19 kg. Leave it out and the leak stays at the parapet foot.

Doubles a bathroom

Forgetting the second layer

A sunken bathroom gets one layer in the sunk and one under the tiles. Count both, and the sunk sides. Bathroom steps.

Takes more

A rough, porous or old slab

Loose mortar, honeycombing and open cracks soak up coat. Fill cracks with SBR mortar first, and buy for the high figure.

Wastes it

Mixing a whole pack at once

Mixed coat that thickens in the bucket is lost. Mix what one person can lay in the time the pack allows.

Wrong product

Damp from inside the wall

Hi-Flex goes on the side the water falls on. Damp rising from the ground needs Seep Blocker 2K on the inner face: Hi-Flex vs Seep Blocker 2K.

Questions people ask us

Short answers

How many kg of Hi-Flex for a 1000 sq ft roof?

134–143 kg for two coats on the flat roof: six 24 kg packs. With the coat taken 1 ft up a 130 ft parapet, about 162 kg: seven 24 kg packs. UltraTech's figure is 14–15 sq ft per kg for one coat, and its method is two coats.

How much Hi-Flex per sq ft?

About 0.14 kg per sq ft for two coats, or 1 kg for every 7 sq ft. That is UltraTech's 14–15 sq ft per kg per coat, doubled.

Some sites say 70 kg for 1000 sq ft. Who is right?

70 kg is one coat (1000 ÷ 14.5). UltraTech asks for two coats of 0.6–0.7 mm, at least 8 hours apart, the second at right angles to the first. Buy for two.

How much Hi-Flex for a bathroom? (bathroom me kitna Hi-Flex lagega)

A 6 × 8 ft bathroom with a 1 ft sunk and bucket bath is 210 sq ft over both layers, 28–30 kg: one 24 kg and one 12 kg pack. Without a sunk, only the layer under the tiles: 106 sq ft, 15–16 kg.

Should I add extra for wastage?

UltraTech gives no wastage figure. We buy for the high end of its range (area × 2 ÷ 14) and round up to whole packs; that is the margin. For a rough old roof, keep one 12 kg pack spare rather than stop halfway.

Can Hi-Flex go inside a drinking-water tank?

UltraTech does not list it for that. Its brochure gives a separate product, Weather Pro Single Component, food-grade approved by CFTRI, at 11 sq ft per kg for two coats. The tank's top and outside can take Hi-Flex. We order Single Component for you.

How much Flex instead of Hi-Flex?

Flex covers 12–14 sq ft per kg per coat (UltraTech), so area × 2 ÷ 12 at the high end. A 1000 sq ft roof is 143–167 kg. It stretches up to 50% against Hi-Flex's 100%. We order it for you.

Does the screed on top change the Hi-Flex quantity?

No. The screed is cement, balu and WP+200 laid over the coat to protect it, which UltraTech "highly recommends". Its quantities are on waterproofing while casting and terrace waterproofing.

Mr Mustafaa
Paint Engineer, Tashya Ventures

Paint and waterproofing at our Reva Road store, Muzaffarpur. Every coverage figure on this page was checked against UltraTech's Weather Pro brochure on 13 Nov 2026, and the roof and bathroom figures match our other waterproofing pages.

Where the numbers come from

  1. UltraTech, Weather Pro waterproofing brochure: Hi-Flex 1 kg of mix covers 14–15 sq ft, Flex 12–14; 0.6–0.7 mm per coat; two coats at least 8 hours apart, the second at right angles; screed over the coat "highly recommended"; positive-side uses including terraces, sloping roofs, walls, balconies, domes, and bathroom, kitchen and sunken areas; packs Hi-Flex 12, 24 kg, Flex 3, 15, 30 kg. Single Component: for drinking-water tanks, food-grade approved by CFTRI, 1 kg + 350–380 ml water covers 11 sq ft in two coats, 2–3 hours apart, packs 1, 5, 25 kg.
  2. Coverage counted per coat and doubled for two coats, as our owner's figure and our Hi-Flex, new roof and bathroom pages count it.
  3. Bathroom wall heights (1 ft all round, 4 ft at the tap wall, 7 ft with a shower): our bathroom page, from Dr. Fixit's 20 cm and Birla White's 300 mm minimums, taking the higher.
  4. Birla White, water tank waterproofing and Seep Blocker Pro 2K page: "Food Grade Certified", recommended for water tanks.
  5. Read for what readers are told elsewhere: StudioMatrx waterproofing material calculator (one generic 1 kg per m² per coat, roof area only), HouseYog waterproofing cost 2026 and Dr. Fixit roof waterproofing cost guide (rupees per sq ft, no kilos).
  6. Parapet strip of 1 ft, wet-wall width, tank sizes in the examples: usual practice, not a maker's figure.

Send us your sizes

Roof, bathrooms, balcony, tank: we send back the kilos, the packs and today's price on WhatsApp.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com