हिंदी Call90310 74624
Home›Bihar›Waterproofing
Bihar house problems · damp walls

Seelan from foundation to roof: the three causes, and the fix at each stage

The short answer

Seelan is water getting into the wall. In a Muzaffarpur house it comes from one of three places, and each has its own fix:

  1. 1From the ground belowA damp band from the floor up, worst on the ground floor. Groundwater rises up a wall that has no damp-proof course (DPC).
  2. 2From rain outsidePatches near the ceiling, on outside-facing walls, under the parapet. Worse after heavy rain.
  3. 3From a bathroom or pipeA patch that spreads from one spot on the wall next to a bathroom, kitchen or pipe line. Wet even in dry months.

Stop the water first, let the wall dry, paint last. Putty and paint on a wet wall is money wasted: the patch comes back next monsoon.

0.67 m
Groundwater after the monsoonAs close as this below ground in Muzaffarpur district (CGWB).
150 mm
DPC above groundWhere the damp-proof course sits (UltraTech).
< 10
Moisture meter, before paintThe green zone in the Birla Opus Salt Seal sheet.
Where the water gets in
Section through a one-storey house showing three ways water gets into the walls 1: groundwater rises from below through a wall with no damp-proof course. 2: rain soaks the parapet and leaks through a crack in the roof slab. 3: a leaking pipe inside the bathroom wall wets the wall of the next room. Groundwater 0.7–5 m down after the monsoon ground Bathroom Room no DPC 1 Rain 2 3
  1. 1Ground: water rises up the brick from below, to 2–3 ft on the inside wall. Stopped at the plinth, by the DPC.
  2. 2Rain: soaks the parapet and outside wall, or ponds on the roof and finds a crack. Stopped at the roof, parapet and outside plaster.
  3. 3Pipe or bathroom: a joint inside the wall, or a bathroom floor without waterproofing, wets the wall next door.
Not to scale. Groundwater depth: CGWB, Muzaffarpur district, 2011 readings (0.67–5.21 m below ground after the monsoon).
Which kind is yours

Look at where the patch is, and when it gets worse

The shape of the patch tells you the source. Check this before buying anything, because each kind needs a different product.

2–3 FT

1Damp from the ground

Where
A band along the bottom of ground-floor walls, often inside and outside, with a wavy tide line.
When
All year; worse in and after the monsoon, and after floods.
Also
White salt along the line, skirting tiles loosening, paint flaking at knee height.
Should have been stopped at: plinth and DPC

2Damp from rain

Where
High on outside-facing walls, at the ceiling corner, under the parapet, below window sills and chhajjas.
When
During and after heavy rain; it shrinks in winter.
Also
Water ponding on the roof, cracks in the parapet top or outside plaster, a dark patch on the outside wall.
Should have been stopped at: roof, parapet, outside plaster
pipe inside the wall

3Damp from a pipe or bathroom

Where
On the wall shared with a bathroom or kitchen, or along a pipe line; rings spreading from one spot.
When
Any season, even in the dry months. Worse when the tap or shower is used.
Also
The tank empties faster than usual, the ceiling below a bathroom is wet.
Should have been stopped at: plumbing test, bathroom waterproofing
Damp everywhere in the monsoon, worst in closed corners and almaris? That can be humid air, not water in the wall. It needs airing and sunlight, not waterproofing. Six kinds of patch, and three checks you can do at home: seelan in the wall, cause by cause.
Neev se chhat tak

Six places in a house where seelan is stopped, from the foundation up

Each one is cheap while the house is being built and costly once it is finished. If you are building now, do all six. If the house is built, the right-hand column is your fix.

The six stages where a house is protected from damp From the bottom: 1 foundation concrete with WP+200, 2 damp-proof course about 150 mm above ground, 3 walls and outside plaster with WP+200, 4 bathroom floor waterproofed and turned up the wall, 5 roof slab with WP+200 and a slope to the drains, 6 parapet with a coping and drip line. ground 1 2 3 4 5 6 Foundation DPC at plinth Walls, outside plaster Bathroom floor Roof slab Parapet, chhajja WP+200 in the concrete ~150 mm above ground WP+200 in the plaster coat turned 300 mm up WP+200, slope to drains coping, drip line, Hi-Flex Read from the bottom up:neev se chhat tak
Not to scale. WP+200 dose and Hi-Flex: UltraTech Weather Pro brochure. DPC height: UltraTech. Bathroom upturn: Birla White Seep Blocker 2K brochure.
StageWhile buildingMissed it? The fix now
1FoundationAdd WP+200 to the foundation and plinth concrete: 200 ml per 50 kg bag of cement.UltraTech Weather Pro brochureCan't be redone. Keep the ground outside sloping away from the wall and the drains clear.
2DPCA continuous damp-proof course across every wall at plinth level, about 150 mm above ground, with WP+200 in its concrete. In low mohallas that flood, raise the plinth.UltraTech · DPC stageRising damp. The step-by-step repair is below, card 1.
3WallsWP+200 in the outside plaster and in the mortar of walls that face the rain. Fill gaps around window frames.UltraTech Weather Pro brochureFill cracks, then a waterproof coat on the outside (Seep Guard Vertical or WallFix 4) under exterior paint. Card 2.
4BathroomTest the pipes under pressure before closing the walls. Waterproof the floor and 300 mm up the walls, 1.8–2.1 m behind the shower. Fill with water for 48 hours before tiling.Birla White Seep Blocker 2K brochureRepair the pipe. If the floor leaks, lift the tiles and waterproof it properly. Card 3.
5Roof slabWP+200 in the dhalai concrete, a slope to the drain spouts, then a Hi-Flex coat with a screed over it.UltraTech Weather Pro brochureClean, fill cracks, two coats of Hi-Flex, screed on top. Full guide: water dripping from the roof.
6Parapet, chhajjaA coping on the parapet top that sheds water outwards, a drip groove under the chhajja, the roof waterproofing turned up the parapet.usual practiceFill cracks on the parapet top, coat it with Hi-Flex, and give parapet tops and chhajjas one extra coat of exterior paint (Birla Opus sheets).
The fix in a finished house

The fix for each kind, in the order the work is done

The products are the ones we keep for each job. Every one can be ordered from us.

1Rising damp from the ground

Ground-floor walls, damp band from the floor
  1. Lower what is outside. Soil, a raised road or an outside floor higher than the plinth feeds the wall. Bring it below the DPC level and keep drains away from the wall (UltraTech).
  2. Cut off the damp plaster down to the brick, up to about 1½ ft above the highest tide mark (usual practice). Where salt shows, Birla White says to take the plaster down to the brick.
  3. Wash, then let the brick dry. Brush off the salt.
  4. Two coats of Seep Blocker 2K on the bare brick, 5–6 h apart, crosswise. It is rated against water from either side, which is what a wall fixed from inside needs.
  5. Re-plaster over a bond coat made with Seal & Dry SBR, with WP+200 in the plaster mortar.
  6. When dry: Salt Seal, waterproof putty, primer, paint. See below.
Putting a new DPC into an old wall (cutting it in or injecting it) is specialist work. These steps hold the damp back for years if the outside stays below the plinth. More: DPC and plinth waterproofing.

2Rain getting in

Roof, parapet, outside walls, sills
  1. Roof first. Clear the drain spouts, cut out and fill cracks, then two coats of Hi-Flex, at least 8 h apart and crosswise, with a screed or plaster over it (UltraTech).
  2. Parapet tops and chhajjas get the same coat. Water that sits on them runs straight into the wall below.
  3. Outside wall: fill cracks and gaps around frames. Then either Seep Guard Vertical (priming coat plus two coats) or AllDry WallFix 4 (a 10% thinned coat plus one full coat) as the waterproof base.
  4. Then exterior primer and 2–3 coats of exterior paint: Style Power Bright or Calista Neo Star.
  5. New plaster on a rain-facing wall: WP+200 in the mortar, 200 ml per bag of cement.
WallFix 4 sheet: not on a wet or visibly damp wall, not above 80% humidity, no rain for 48 h after. Opus exterior sheets: no rain within 4 days. So do outside work between October and May.

3A bathroom or pipe leak

Wall next to a bathroom or kitchen, ceiling below a bathroom
  1. Find it. Close every tap and watch the meter or the tank level for an hour. If it drops, a pipe is leaking. If not, the bathroom floor or the tile joints are letting water through.
  2. Pipe: open the wall at the patch and repair or replace the joint. Leaking pipe joint.
  3. Floor: lift the tiles. A bond coat with Seal & Dry SBR, then two coats of Hi-Flex or Seep Blocker 2K, 300 mm up the walls and 1.8–2.1 m behind the shower.
  4. Pond test: 50 mm of water for 48 hours with the drains closed. No damp below, then screed and tile (Birla White).
  5. Grout the joints with TileLynk grout, not plain cement.
Water coming through to the room below: bathroom water in the room below · whole job: bathroom waterproofing.
Only after the water is stopped

Dry the wall, then build it back up in this order

This is where most money is lost: painting a wall that is still wet. Both Birla White and Birla Opus say to stop the source and let the wall dry before their products go on. For the paint layers themselves, see putty, primer, paint.

1Is it dry?

Let the wall dry fully: usually a few weeks after the leak is fixed, longer in the monsoon. Test by touch and colour. No cool feel, no dark patches, no tide line growing. If you have a moisture meter, the Birla Opus Salt Seal sheet wants a reading below 10 (the green zone).

2Salt marks? Salt Seal first

Brush off the white salt, then one coat of AllDry Salt Seal thinned 1 L with 1 L of water. It blocks the salt so the paint stays on. Wait 4–6 h. It covers 80–100 sq ft per litre. More: white salt on walls.

3Waterproof putty, two thin coats

Birla White WallSeal waterproof putty in place of plain putty. Wet the wall first, 36–38% water, 3–4 h between coats, both coats together no more than 1.5 mm, 24 h before paint.

4Primer, then two coats of paint

Birla White says WallSeal needs no primer. The Birla Opus paint sheets put primer before the paint, so we follow the paint sheet. It costs one thin coat.

A ground-floor wall after the repair
Layers of a wall repaired for rising damp From the brick outwards: brick, two coats of Seep Blocker 2K, an SBR bond coat, new plaster with WP+200, Salt Seal, two coats of waterproof putty, primer, two coats of paint. ROOM → ✓ 1 2 3 4 5 6 7 8 Brick, dried Seep Blocker 2K × 2 SBR bond coat New plaster Salt Seal Waterproof putty 1 Waterproof putty 2 Primer Paint × 2 old plaster cut off 2 kg powder : 1 kg liquid cement + SBR + sand WP+200: 200 ml / bag 1 L + 1 L water, 1 coat pre-wet the wall both ≤ 1.5 mm as the paint sheet says interior emulsion
Not to scale. Seep Blocker 2K mix and the bond coat: Birla White brochure. WP+200: UltraTech. Salt Seal: Birla Opus sheet SS002/08/2024. Putty: Birla White WallSeal brochure.
What doesn't work

Four repairs people pay for twice

Fresh paint on a damp wall

You see: bubbles and peeling within months

The water is still coming. It pushes the paint off from behind. Stop the source and dry the wall first.

WATERPROOF PUTTY OVER A LEAK

Waterproof putty over a leak

You see: the stain comes back

Birla White itself says waterproof putty cannot repair plumbing leaks, roof leakage or active seepage. It is the finish after the fix.

A cement band only at the bottom

You see: the damp line moves higher

Sealing just the lower part of a wall that has rising damp leaves the water nowhere to go but up. What masons see: the tide mark climbs above the new band. Treat the source and the full damp height.

NO SCREED OVER THE COAT

Roof coating left bare

You see: it wears through where people walk

UltraTech recommends a screed or plaster layer over Hi-Flex. Without it, the thin coat takes the sun and every footstep directly.

How much for one damp wall

Material for a rising-damp repair on one wall

Put in the wall length and the height of the damp. We add 1½ ft above the tide mark, as the plaster is cut back that far. Quantities use the makers' coverage figures.

Area to treat: — sq ft

Damp on both faces of the wall? Work out each face separately. Re-plastering: WP+200 at 200 ml for every bag of cement your mason uses.

Your list

Seep Blocker 2K, 2 coats—7.5–8 sq ft per kg for two coats (Birla White)—
AllDry Salt Seal, 1 coat—80–100 sq ft per litre, before water is added (Birla Opus)—
Waterproof putty, 2 coats—16–19 sq ft per kg on a smooth surface (Birla White)—
Material totalAsk rate
Send this list on WhatsApp

Packs are for the high number. Prices are filled in from today's rate. Roof or bathroom: waterproofing calculator.

Questions people ask us

Short answers

Why does seelan come into walls here? (deewar me seelan kyu aati hai)

From one of three places: groundwater rising up the wall from below, rain getting in through the roof, parapet and outside walls, or a leaking bathroom or pipe. In Muzaffarpur the first is common because the water table is shallow: CGWB recorded it 0.67–5.21 m below ground after the 2011 monsoon, and the district gets 85% of its 1,280 mm of rain between June and September.

Will waterproof paint or waterproof putty stop seelan?

Not on its own. Birla White says its waterproof putty cannot repair plumbing leaks, roof leakage or active seepage. The Birla Opus Salt Seal sheet says to find and stop the water, let the wall dry, and only then apply. Putty and paint are the last step.

How long should the wall dry before putty and paint?

Until it is fully dry, which is usually a few weeks after the leak is fixed, and longer in the monsoon. Test by touch and colour: no cool or dark patches, no tide line growing. The Birla Opus Salt Seal sheet asks for a moisture meter reading below 10.

Can rising damp be fixed in an old house that has no DPC?

It can be held back. Keep the soil and outside floor below the plinth, cut off the damp plaster to the brick, coat the brick with Seep Blocker 2K, re-plaster with WP+200 in the mortar, then Salt Seal and waterproof putty before paint. Putting a new DPC into an old wall is specialist work.

Seep Guard or Seep Blocker: which one for my wall?

Birla White makes Seep Guard Vertical for outside walls, the side the rain hits. Seep Blocker 2K is a two-part coating rated against water from either side, so it suits the inside face of a damp wall, bathrooms and kitchens. For the roof, use Hi-Flex or Seep Guard Horizontal.

Does seelan harm the house, or only the paint?

Both. UltraTech's Weather Pro guide says dampness corrodes the steel and cracks the RCC over time. It also brings fungus and a musty smell into rooms. Fix it before it reaches the slab steel.

Ghar me seelan vastu: is it a vastu dosh?

People ask this often. Whatever one believes about vastu, the water in the wall has a building cause: ground, rain or a pipe. Fixing that cause is what dries the wall.

Will you come and check my wall?

Send us photos of the patch on WhatsApp: the whole wall, close up, and the outside of the same wall. We will look at them with you and tell you which of the three it looks like and what to buy.

Mr Mustafaa
Paint Engineer, Tashya Ventures

Paint and waterproofing at our Reva Road store, Muzaffarpur. Every number on this page was checked against the maker's own sheet or brochure on 12 Nov 2026. Where two figures disagree, the page says so and gives the safer one.

Where the numbers come from

  1. Central Ground Water Board, Ground water information booklet, Muzaffarpur district: depth to water 2.09–7.63 m (pre-monsoon) and 0.67–5.21 m (post-monsoon) below ground in 2011; average rainfall 1,280 mm, 85% in June–September; floods from the Burhi Gandak and Baghmati.
  2. UltraTech, How to prevent dampness in walls: penetrating, rising and condensation damp; DPC about 150 mm above ground; keep the soil below the DPC.
  3. UltraTech, Weather Pro waterproofing brochure: WP+200 at 200 ml per 50 kg bag, added to half the mixing water; Hi-Flex 0.6–0.7 mm per coat, two coats at least 8 h apart crosswise, 14–15 sq ft per kg, 12 and 24 kg, screed or plaster recommended on top; dampness corrodes steel and cracks RCC.
  4. Birla White, Seep Guard Seep Blocker 2K brochure: mix 2:1 powder to liquid, positive and negative side up to 5 bar, coats 5–6 h apart, total 1–1.2 mm, 7.5–8.0 sq ft per kg for two coats, 3 and 15 kg, 3-year warranty; pressure-test plumbing first; plaster down to brick where salt shows; bathroom 300 mm up the walls, 1.8–2.1 m at the shower; 48 h pond test at 50 mm.
  5. Birla White, Seep Guard Vertical Surfaces brochure: exterior vertical walls; priming coat 1 kg + 1 L water, then coats at 600–650 ml per kg, 4–6 h apart crosswise, total up to 1 mm; 24–26 sq ft per kg on plaster; 10–12 h before the top coat; 15 kg; 8-year warranty.
  6. Birla White, WallSeal waterproof putty brochure: interior and exterior; pre-wet; 36–38% water; 3–4 h between coats; both coats up to 1.5 mm; 24 h before paint; 16–19 sq ft per kg; "no primer is required".
  7. Birla White, Waterproof putty vs regular putty: waterproof putty cannot repair plumbing leaks, roof leakage or active seepage.
  8. Birla Opus, AllDry Salt Seal information sheet (SS002/08/2024): alkali-block primer against efflorescence; 1 L + 1 L water, one coat, 4–6 h recoat; 80–100 sq ft per litre in the application table (the front gives 100–120, so we use the lower); 1, 4, 20 L; stop seepage and dry the wall first; moisture meter below 10. Same sheet: no rain within 4 days.
  9. Birla Opus, AllDry WallFix 4 information sheet: waterproofing basecoat for parapets, sunshades and exterior walls; 10% thinned coat, then one undiluted coat; 40–45 sq ft per litre; 4–6 h; not on wet or damp surfaces, not above 80% humidity, no rain within 48 h; 1, 4, 10, 20 L.

Send us a photo of the damp wall

The whole wall, a close-up and the outside of the same wall. We'll tell you which kind it looks like and send the list, with today's price, on WhatsApp.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com