हिंदी Call90310 74624
Home›Problems and fixes›Waterproofing
Problem · damp walls

Seelan in the wall: where it comes from, how to tell, and the fix for each cause

The short answer

Seelan is water getting into the wall from one place. Where the patch sits tells you which place:

  1. 1Low on a ground-floor wall, with a wavy line: water rising from the ground. Fix ›
  2. 2High, where the wall meets the ceiling on the top floor: the roof or parapet. Fix ›
  3. 3On the wall shared with a bathroom: the bathroom floor, joints or pipes. Fix ›
  4. 4On an outside wall, worse after rain: rain soaking through. Fix ›
  5. 5A round patch on a pipe line, wet even in dry weather: a leaking pipe. Fix ›
  6. 6Many walls, in corners, only in monsoon: damp air, not a leak. Fix ›

Putty and paint on a wet wall is money wasted. Stop the water first, let the wall dry, then repaint.

6
Places water comes fromEach needs a different fix. Most houses have one, some have two.
2–3 ft
How high ground damp climbsWhat we see in Muzaffarpur houses. Higher than that, look at the roof or a pipe.
Weeks
Drying before puttyNot days. Test the wall by touch and colour, not the calendar.
WhatsApp a photo of the patch Send one close photo and one of the whole wall, floor to ceiling, and say which floor it is on. We'll tell you which of the six it looks like.
Where the patch is tells you the cause
A two-storey house cut open, showing six places seelan appears 1: a band low on a ground-floor wall with a wavy line, from ground water rising. 2: a stain where the top-floor wall meets the ceiling, from water standing on the roof and a crack at the parapet. 3: a stain on the wall next to the bathroom. 4: a stain on the inside of an outer wall hit by rain. 5: a round stain on the line of a pipe coming down from the roof tank. 6: black spots in the corner of a closed room, from damp air. ground water, high after monsoon and floods bathroom tank 1 2 3 4 5 6 1 2 3 4 5 6 From the groundRoof, parapetBathroom Rain, outer wallLeaking pipeDamp air
Most houses have one of these, some have two. A patch can also travel: water from a roof crack can show up a few feet away, so check the nearest likely source first.
Find yours

Six kinds of seelan: what each looks like, and what to fix first

Match your wall to a picture. Each card says how to confirm it, what has to be fixed before anything else, and the product for that job. All of them can be ordered from us.

2–3 ft wavy tide line, white salt along it
1

Low on a ground-floor wall

Cause: water rising from the ground
How to confirm
The band starts at the floor, stops at a wavy line, and is often worst late in the monsoon and after floods, when ground water is high. Paint flakes and white salt sit on the line. Common in old houses built without a damp-proof course (DPC) and in low-lying mohallas.
Fix first
Inside, scrape off the damaged putty and plaster up to a foot above the line. A true cure is a DPC, a specialist job in an old house. What manages it: a coating on the inside face of the lower wall and a waterproof plaster. After a flood, dry the house out first: damp after a flood.
Products
Seep Blocker 2K, inside faceWP+200 in new plasterSalt SealWaterproof putty
starts at the ceiling worse within a day of rain
2

High, where the wall meets the ceiling

Cause: the roof slab or the parapet joint
How to confirm
Top floor only. It starts at the ceiling line, usually in a corner, and gets worse within a day of heavy rain. Go up after rain: water standing on a flat roof, a blocked outlet, or a crack where the parapet meets the slab (the gola) is the culprit.
Fix first
Clear the outlets and fix the slope so no water stands. Fill cracks and make a fillet at the parapet joint with SBR mortar. Then coat the roof and carry the coating up the parapet. UltraTech says Hi-Flex goes on in two coats, at least 8 hours apart, laid crosswise, at 14–15 sq ft per kg, with a screed or plaster over it.
Products
Hi-Flex coatingSeal & Dry SBRWP+200 in repair mortar
bathroom behind wettest next to the bathroom wall
3

On the wall shared with a bathroom

Cause: open tile joints, the floor trap, or the pipes inside
How to confirm
Wettest right against the bathroom and fading away from it, worst in the morning after baths. If the patch shrinks when nobody uses the bathroom for two or three days, it is the floor or joints. If it stays wet, it is a pipe in the wall (see 5).
Fix first
Cheapest first: re-grout the open joints, seal round the floor trap and pipe sleeves with SBR mortar. If the floor itself is soaked, the tiles come up and the floor is redone with SBR in the base coat and Hi-Flex under the new tiles.
Products
Seal & Dry SBRHi-Flex under tilesSeep Blocker 2K, small floorTileLynk grout
worse after rain under window corners OUTSIDE
4

On an outside wall, worse after rain

Cause: rain soaking through cracks, bare plaster or window joints
How to confirm
Only on walls that face outside, mostly the one the rain hits, at any height. Worse during and just after rain, drier in winter. Look outside: hairline cracks, missing paint, a gap round the window frame, or a dripping chhajja.
Fix first
Fix it from the outside; inside-only work does not last. Fill cracks with SBR mortar, seal window joints, add WP+200 to any new plaster (UltraTech: 200 ml per 50 kg bag of cement), then Seep Guard Vertical and exterior paint. Birla White gives Seep Guard Vertical an 8-year waterproofing warranty if you register it within 30 days.
Products
Seep Guard VerticalWP+200SBR for cracksExterior paintWaterproof putty inside
round, on the pipe line wet even in May hidden pipe
5

A round patch on a pipe line

Cause: a leaking joint in a hidden water pipe
How to confirm
Round, darkest in the middle, on the line a pipe would take: below the roof tank, behind a tap, beside a kitchen sink. Wet in every season, even in the May heat. The pipe check below settles it.
Fix first
This is a plumber's job, not waterproofing. No coating holds back a pipe under pressure. Open the wall at the patch, replace the joint or that length of pipe, and patch the chase with SBR mortar. Then let it dry like any other seelan.
Products
CPVC pipes and fittingsSBR to patch the chase
corners, behind furniture, no line musty smell
6

Many walls, in corners, only in monsoon

Cause: damp air settling on cool walls (condensation)
How to confirm
Black or green spots rather than a brown stain, in corners, behind an almirah or bed, in rooms kept shut. No tide line, no one source. Comes in the monsoon and goes in the dry months. The plastic-sheet check shows water on the room side.
Fix first
Air, not waterproofing. Open windows on dry days, keep furniture a few inches off the wall, run an exhaust fan in the bathroom and kitchen. Wipe the spots off. Repaint only after the monsoon, on a dry wall. Opus says not to paint at all above 90% humidity.
Products
No waterproofing neededExhaust fan (we order it)
Not sure which one?

Three checks you can do at home, free

None of these needs a meter or a mistri. They tell you whether water is coming through the wall, from a pipe, or from the air.

wet UNDER: wall wet ON TOP: air

1Plastic sheet on the patch

Tape a one-foot square of clear plastic or foil on the patch, all four edges sealed. Look after two days. Drops underneath: water is coming through the wall (1 to 5). Drops on top: damp room air (6).

night morning →

2The pipe check

At night, after the last use, switch off the motor, mark the water level in the tank and use no water till morning. Level dropped with every tap shut: a pipe is leaking. Then shut the valve to one line at a time to find which. A patch that stays wet in May points the same way.

1 Jul 8 Jul, after rain

3Mark it and watch

Draw round the patch in pencil and write the date. Check after rain, after the bathroom is used, and after a week of nothing. What makes it grow is the cause. The table below reads the result.

When is the patch at its worst?
It grows or darkens…Most likely
Within a day of heavy rain, top floor, from the ceiling2 · Roof
During and just after rain, on a wall facing outside4 · Outer wall
Late monsoon and after floods, low down, lasts into winter1 · Ground
Mornings after baths, next to the bathroom3 · Bathroom
All year, even in May, round and on a pipe line5 · Pipe
Monsoon only, many rooms, spots in corners6 · Damp air
After the water is stopped

Dry first, repaint last: the order that doesn't waste money

This is the same for every cause. The only step people skip is the second one, and it's the one that decides whether the new paint lasts.

  1. Stop the water at its sourceRoof, bathroom, pipe, outside wall or ground: the card above for your patch. Nothing below works until this is done.
  2. Let the wall dry fullyUsually a few weeks after the leak is fixed, longer in the monsoon. Go by the four signs in the box below, not by a date.
  3. Scrape back to sound plasterRemove all loose paint, puffed putty and powder. Where plaster sounds hollow when tapped, cut it out and re-plaster, with WP+200 in the mortar on a wall that gets wet.
  4. Treat salt if there is white powderBrush it off dry, never wash it back in. Then AllDry Salt Seal before anything else. More: white salt on walls.
  5. Waterproof putty, in place of plain puttyBirla White WallSeal, two thin coats. Birla White says it has twice the water resistance of ordinary putty. It helps the finish last on a damp-prone wall. It does not stop a live leak. More: putty on a seelan wall.
  6. Primer, then two coats of paintThe usual system, with the same waiting times: putty, primer, paint. Opus says not to paint when humidity is above 90%.

Is the wall dry yet? All four must be yes

  • Same colour as the dry wall next to it, with no darker edge.
  • Not cool to the back of your hand compared with a dry wall.
  • The plastic sheet stays dry underneath for two days.
  • No new white powder for two weeks after brushing.

New plaster is different again: Birla Opus asks for 28 days of curing, then a dry wall, before painting.

Why paint on a wet wall fails
Water in the wall pushing off new putty and paint Left: a wall cut open, still wet. Water moving through the brick and plaster carries salt to the surface, where it lifts the putty and paint in bubbles and flakes. Right: the same wall after the source is stopped and it has dried. The finish stays on. STILL WET water in the wall carries salt out, lifts the finish bubblebubbleflake SOURCE FIXED, DRY Salt SealWP puttyprimerpaint nothing pushing out the new finish stays on
Not to scale. "Waterproof" putty and paint resist dampness; they are not built to hold back water that is still moving through the wall. That is why the source comes first.
On our shelf for seelan

The products, and which cause each one is for

Figures are from each maker's own sheet or pack. Anything not on the shelf that day, we order for you; ask on WhatsApp how long it takes.

Seal & Dry SBR has no product sheet on UltraTech's site, so mix it as the pack says. Our 3 kg Seep Blocker 2K covers about 22–24 sq ft in two coats at Birla White's 7.5–8 sq ft per kg. Quantities for a roof or bathroom: waterproofing calculator. Today's prices: waterproofing rates. All products: waterproofing.

Questions people ask us

Short answers

What is seelan in English?

Damp, or dampness. When water is visibly coming through a wall it is called seepage, and the white powder it leaves is efflorescence (white salt on walls).

Will waterproof putty or paint on the inside stop seelan?

No. Waterproof putty resists moisture so the finish lasts longer on a damp-prone wall, but nothing put on the inside face holds back water that is still getting into the wall. Stop the water at its source first. The one inside coating made to take water pushing from behind is a cementitious one like Seep Blocker 2K, which Birla White tests at 5 bar from both sides, and even that is for the lower wall after the outside has been dealt with.

How many days after fixing the leak can I put putty and paint? (seelan ke kitne din baad paint)

There is no fixed number. Let the wall dry fully: the same colour as the dry wall around it, not cool to the touch, and a plastic sheet taped on it stays dry underneath for two days. Usually that takes a few weeks after the leak is fixed, longer in the monsoon.

Can I put tiles on the lower wall to hide rising damp?

It hides the patch but not the water. The wall can no longer dry from that face, so the damp usually climbs above the tiles, and tiles on a wet wall can come loose. Deal with the ground water first (plinth and DPC).

Why does seelan come only in the monsoon?

Either rain is getting in through the roof or an outside wall, or the ground water has risen and is climbing the wall from below. North Bihar's ground water rises a long way in the monsoon and after floods. Where the patch sits and when it is worst tell you which.

Do home remedies like vinegar or bleach cure seelan?

They clean the black mould off the surface and that is all. The mould comes back as long as the wall stays wet.

I'm building now. How do I avoid seelan later?

WP+200 in the foundation, plinth and DPC concrete, the roof slab and outside plaster, at UltraTech's 200 ml per 50 kg bag of cement; a proper DPC at plinth level; a raised plinth in low-lying areas; and a waterproofed bathroom floor before tiling. More: waterproofing while building.

Can you come and see the wall?

We don't do free site visits. Send photos on WhatsApp, one close and one of the whole wall, with the floor and which side of the house, and we'll look at them with you and say which of the six it looks like.

Mr Mustafaa
Paint Engineer, Tashya Ventures

Paint Engineer at our Reva Road store, Muzaffarpur, looking after paint, putty, tiles and waterproofing. Every product figure on this page was checked against the maker's own sheet or pack on 12 Nov 2026. Where a maker publishes no figure, the page says so.

Where the numbers come from

  1. UltraTech, Weather Pro waterproofing brochure: WP+200 at 200 ml per 50 kg bag, half the water with the dry mix and WP+200 in the other half; Hi-Flex two coats of 0.6–0.7 mm, at least 8 h apart, crosswise, 14–15 sq ft/kg, 12 and 24 kg, screed or plaster on top.
  2. Birla White, Seep Guard Vertical Surfaces and its warranty card: exterior plastered walls, 8-year waterproofing warranty, registration within 30 days, top coat of paint recommended.
  3. Birla White, Seep Blocker 2K: tested at 5 bar positive and negative water pressure (EN 12390-8), 7.5–8.0 sq ft/kg in two coats, second coat after 6–8 h.
  4. Birla White, WallSeal Waterproof putty: "2x water resistance", for plaster, concrete and mortar; pack sizes 1, 5, 20, 30, 40 kg (wall putty range).
  5. Birla Opus, Style Color Smart product information sheet: 28-day plaster cure, no painting above 90% humidity.
  6. Birla Opus AllDry Salt Seal: the 1 L, 4 L and 20 L packs; coats and thinning as printed on the pack.
  7. Rising damp height (2–3 ft), the checks and the timing table: what we see in Muzaffarpur houses, labelled as usual practice, not a maker's figure.

Send us a photo of the patch

One close, one of the whole wall. We'll tell you which cause it looks like and what to buy for it, with today's price, on WhatsApp.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com