हिंदी Call90310 74624
Home›Problems and fixes›Damp walls
Wall problem · deewar par namak

White salt on walls: why it keeps coming back, and what actually stops it

The short answer

The white powder is salt from inside the wall: from the brick, the sand and the cement. Water carries it out and dries off; the salt stays. It is called efflorescence. Brushing it off and repainting lasts a few weeks, because the water is still coming. Do it in this order:

  1. 1Stop the water
  2. 2Let it dry
  3. 3Brush off dry
  4. 4Salt Seal or Saltblock
  5. 5Primer and paint
No water
No saltSalt can only travel in water. A salty wall is a wall that gets wet from somewhere.
Weeks
To dry, after the leak is fixedTest by touch and colour, not by the calendar.
1 coat
Of Salt Seal on the plaster1 L with 1 L water. Or 2 coats of Saltblock putty instead of normal putty.
How the salt gets to the surface
Cross-section of a ground-floor wall with salt coming out Read from the bottom up. Water from the ground rises into the brick wall, dissolves salt from the brick, sand and cement, and dries off at the wall face. The salt stays behind as white powder along a tide mark, and crystals growing under the paint push it off. Above the wet zone the wall is clean. 1 2 3 4 5 6 Water comes in Picks up salt Dries off here Salt stays Crystals grow Paint falls off Dry wall: clean ground, a leak, rain from brick, sand, cement the water leaves as vapour white powder, tide mark under the paint: it bubbles a season after repainting no water, no salt GROUND WATER ROOM FLOOR read from the bottom up ↑
Rising damp from the ground is the commonest case in Muzaffarpur, but a roof, bathroom or rain leak works the same way. Not to scale.
First, check what it is

Is it salt, fungus, a damp stain or old paint?

Four things look alike from a distance and need different fixes. Rub the patch with a dry finger before you buy anything.

Salt

White, dry, crunchy powder

Rubs off as white grit whatever the paint colour. Sits low on the wall or along a wet line, and comes back in the same place after brushing. This page is for you.

Not salt

Black or green spots

Fungus or algae. Feels damp or slimy, grows in corners and behind furniture. Needs cleaning and air, not a salt sealer: fungus and algae on walls.

Not salt yet

Brown rings, no powder

A water stain. The same water will bring salt later. Start with the leak: damp in walls.

Not salt

Paint colour comes off on your finger

Chalking: old or weak paint breaking down in sun and rain. Clean, prime and repaint: repainting old walls.

Still not sure? Brush a patch clean today and look again in a week or two. Salt comes back in the same place. Or send us a close photo on WhatsApp with a coin beside the patch, and we will tell you which it is.

Step one is always the water

Where the patch is tells you where the water comes from

Salt marks the place where water leaves the wall. Find the place where it enters, and fix that first. Nothing you put on the surface will hold while water keeps arriving.

House section showing four places salt appears A two-storey house. A: salt low on ground-floor walls from water rising out of the ground. B: salt near the ceiling under the roof and parapet. C: salt on the wall next to and below a bathroom. D: salt on the outside face of a wall that takes the rain. A B C D bathroom ground water roof and parapet
White marks show where salt usually appears. Blue shows where the water comes from.
A

Low on ground-floor walls, both sides

Water rising from the ground through the plinth (rising damp). Common in Muzaffarpur's low, wet plots and after floods. Fix: neev, plinth and DPC, with Seep Blocker 2K on the inside face of the wall, then waterproof putty.

B

Near the ceiling, top floor

Roof or parapet leak. Fix the roof with UltraTech Weather Pro Hi-Flex and WP+200 in the repair mortar: parapet leaks.

C

Next to or below a bathroom

Bathroom floor or pipe leak. Fix with Seal & Dry SBR in the base coat and Hi-Flex under the tiles: bathroom waterproofing.

D

Outside face, worse after rain

Rain soaking into the plaster. Fix with WP+200 in the plaster and Birla Opus exterior paint: outside walls.

New house, salt in the first year, all over? New brick and plaster hold a lot of building water. As it dries out it brings salt with it. Birla Opus calls this primary efflorescence and makes Salt Seal for it. It usually settles after the walls dry out once. If it is still coming after the second monsoon, look for one of A to D. Full guide: damp in walls, cause by cause.

Why it comes back

Brushing and repainting is the most common, and costliest, mistake

The wall looks fine for a few weeks. Under the new paint the water keeps bringing salt, and the crystals push the new paint off, usually by the next monsoon. You have paid for the paint and the labour twice.

Repainting over salt without stopping the water Three pictures of the same wall. Day 1 after repainting: clean. Two months later: white powder back along the bottom. Next monsoon: paint bubbled and flaking, plaster showing. Under all three, water keeps coming in. DAY 12 MONTHSNEXT MONSOON fresh paint water still coming in, all the time
What people tryWhy it doesn't hold
Brush off and repaintWater still arrives, salt forms again under the new coat.
Wash the wall with lots of waterPuts more water in. The salt dissolves and comes straight back out as the wall dries.
Normal putty over the saltSalt pushes the putty off with the paint. Ordinary putty is porous, Birla White says.
A thicker coat of paint, or oil paintPushed off the same way. A tight film can trap the water and make bubbles worse.
Salt Seal or Saltblock on a wet wallBoth makers say: stop the water and let the wall dry first. On a wet wall even these fail.

Peeling has other causes too. If there is no white powder under the flakes, see paint peeling.

The fix

Six steps, in this order. Skipping the first two is why most repairs fail.

Six steps to fix a salty wall A staircase of six steps: 1 stop the water, 2 let it dry, 3 brush off the salt, 4 Salt Seal or Saltblock, 5 putty, 6 primer and paint. A red crossed-out arrow shows the shortcut of brushing and repainting straight away. 1 2 3 4 5 6 Stopwater Let itdry Brushoff dry Salt Seal/ Saltblock Putty2 coats Primer+ paint Brush and repaint comes back in a season
  1. Stop the water

    Use the map above to find where it comes in. Fix that first, whether it is the plinth, roof, bathroom, a pipe or an outside wall. If you skip this, every rupee after it is wasted.

  2. Let the wall dry fully

    Usually a few weeks after the leak is fixed, longer in the monsoon. Test by touch and colour: a dry wall feels the same as the dry part above it and has no dark patches. Scrape off loose, flaking paint and crumbly putty now so the wall can breathe out.

    Birla White's Saltblock sheet asks for any damp to be treated and the wall made dry before its putty goes on. Birla Opus says the same for Salt Seal.
  3. Brush the salt off, dry

    Use a stiff brush on the dry wall and sweep up the powder. Wear a mask; the dust is fine. Dry brushing adds no new water to the wall.

    Hard crust that won't brush off? The makers clean differently. Birla White's method is a mild acid (1 part hydrochloric acid to 10 parts water, or a ready efflorescence remover) brushed on gently, then a rinse with clean water. Birla Opus suggests water or a pressure washer. If you wet the wall either way, let it dry again before the next step. Use gloves and eye protection with acid.
  4. Put on a salt-blocking layer

    Either one coat of Birla Opus AllDry Salt Seal on the plaster (1 L with 1 L water, 4–6 h to dry), or skip it and use Birla White Saltblock putty in step 5. Which one: see below.

  5. Putty, two thin coats

    After Salt Seal: Birla White Waterproof putty. Or Saltblock putty on its own, on the pre-wetted wall, 3–4 h between coats. Both coats together no thicker than 1.5 mm. How to work putty on a wall that has been damp: putty on a seelan wall.

  6. Primer, then two coats of paint

    The normal system from here: putty, primer, paint: order and drying times. Outside walls get Salt Seal then 2–3 coats of exterior paint, with no putty.

Salt Seal or Saltblock

Two ways to block the salt. Pick one, not both.

Salt Seal is a primer that goes on the plaster under the putty. Saltblock is a putty that takes the place of your normal putty. They do the same job at different layers, so you need one or the other.

The three layer systems
Layer systems for salty walls Inside, way 1, from the plaster up: Salt Seal one coat, waterproof putty two coats, primer, paint two coats. Inside, way 2: Saltblock putty two coats, primer, paint two coats. Outside: Salt Seal one coat, exterior paint two to three coats. INSIDE · WAY 1INSIDE · WAY 2OUTSIDE PlasterPlasterPlaster Salt Seal × 1Salt Seal × 1 Waterproofputty × 2 Saltblockputty × 2 PrimerPrimer Paint × 2Paint × 2 Exteriorpaint × 2–3 Birla Opus + Birla WhiteBirla WhiteBirla Opus
All three start on a wall that is dry and brushed clean. Salt Seal's 8-year system warranty is for outside walls under Birla Opus exterior paint; Saltblock carries a 1-year efflorescence warranty from Birla White.

Way 1: Salt Seal + Waterproof putty

Inside walls. Both products are on our shelf.
Salt Seal × 1Waterproof putty × 2PrimerPaint × 2
  • AllDry Salt Seal: Birla Opus calls it an alkali-block primer that sinks into the plaster pores. 1 L with 1 L water, one coat, 4–6 h before the next layer.
  • Then Waterproof putty in place of normal putty, then interior primer and paint.
Don't tint Salt Seal. Don't apply below 10°C or above 40°C (Birla Opus sheet).

Way 2: Saltblock putty

Inside walls. We order it for you; ask on WhatsApp for the time it takes.
Saltblock × 2PrimerPaint × 2
  • A white cement putty with anti-salt additives, from Birla White. 1 kg putty with 360–380 ml water, rest 5 min, use within 3–3.5 h.
  • Pre-wet the wall. 3–4 h between coats, about 24 h before primer, and primer and paint within 30 days.
Sand the last coat only lightly, with fine paper of 500 grit or finer. Birla White says rough sanding breaks the salt-blocking layer.

Outside walls

Parapets, boundary walls, the outer face of the house
Salt Seal × 1Exterior paint × 2–3
No rain likely for 4 days. Don't leave Salt Seal alone, or one coat of paint, through the monsoon.
Birla Opus AllDry Salt SealBirla White Saltblock putty
What it isPrimer (alkali-block, water-thinned)White cement putty, anti-salt
Coats12, both together ≤ 1.5 mm
Mix1 L + 1 L water1 kg + 360–380 ml water
Covers80–100 sq ft per litre (sheet also prints 100–120)10–12 sq ft per kg (product page) to 17–20 for 2 coats (brochure)
Next layer after4–6 hAbout 24 h, then primer
Packs1, 4, 20 L5, 40 kg
WarrantyUp to 8 years as a system, outside, under Opus exterior paint1 year, against salt
At our storeOn the shelf, 1 L, 4 L and 20 LWe order it; ask on WhatsApp for the time

Where a maker prints two figures, we buy for the lower coverage so you don't run short. Birla White's own putty calculator asks "white stains on walls before?" for exactly this reason: a wall that has shown salt needs one of these systems, not plain putty.

How much to buy

Material for the salty part of your wall

Treat about 2 ft above the highest white mark (usual practice: salt spreads under the paint before it shows), or the whole wall if you want the finish to match.

Area to treat: — sq ft

Your list

AllDry Salt Seal, 1 coat—80–100 sq ft per litre, before adding water (Birla Opus)—
Waterproof putty, 2 coats—17–20 sq ft per kg, Birla White's figure for its wall putty in 2 coats. Check the bag.—
Material totalAsk rate
Send this list on WhatsApp

Packs are worked out for the higher number. Primer and paint for the room: room calculator. Today's prices: putty rates · paint rates.

Questions people ask us

Short answers

Why does white salt come on walls? (deewar par namak kyun aata hai)

Water moving through the wall dissolves salts in the brick, sand and cement. At the surface the water dries off and the salt stays behind as white powder. No water, no salt: a salty wall is a wall that is getting wet from somewhere. Find where.

How do I remove salt from the wall?

Once the water is stopped and the wall is dry, brush the powder off dry with a stiff brush. For a hard crust, Birla White's method is a mild acid wash (1 part hydrochloric acid to 10 parts water) followed by a rinse with clean water. Then let the wall dry again before sealing.

Which wall putty stops salt stains?

Birla White Saltblock, an anti-salt putty, put on in two coats instead of your normal putty. The other way is one coat of Birla Opus AllDry Salt Seal on the plaster, then waterproof putty. Neither works on a wall that is still wet; both makers say to stop the water first.

Can I paint over a salty wall?

Only after the water is stopped, the wall has dried, the salt is brushed off and Salt Seal or Saltblock putty is on. Paint put straight over salt gets pushed off by the crystals, usually within a season.

Can I use Salt Seal and Saltblock together?

There is no need. Salt Seal is a primer under the putty; Saltblock is the putty. Use one. If you use Salt Seal inside, follow it with waterproof putty.

My house is new and the salt came in the first year. Will it stop?

Often, yes. New brick and plaster hold a lot of building water, and as it dries out it brings salt with it. Birla Opus calls this primary efflorescence and makes Salt Seal for it. If the salt is still coming after the second monsoon, look for a water source.

Is salt on the wall harmful to the house?

The powder is a warning that water is moving through the wall. Left for years, the crystals break up the paint and the face of the plaster. Find and stop the water while the damage is still on the surface.

White powder on the floor tiles or roof?

That is salt from water under the tiles. Different fix: white powder at tile joints.

Mr Mustafaa
Paint Engineer, Tashya Ventures

Paint Engineer at our Reva Road store, Muzaffarpur. Every figure on this page was checked against the maker's own sheet on 12 Nov 2026. Where Birla Opus and Birla White differ, the page says so and goes with the safer choice.

Where the numbers come from

  1. Birla Opus, AllDry Salt Seal information sheet (product code 936001): alkali-block primer for primary efflorescence, 1:1 with water, 4–6 h, 80–100 sq ft/L (100–120 also printed), 1/4/20 L, white, do not tint, 10–40°C, stop seepage and dry first, up to 8-year system warranty on exterior walls.
  2. Birla Opus, AllDry Salt Seal product page (FAQ): inside and outside walls, one coat, not a finish on its own.
  3. Birla White, SaltBlock Anti-Efflorescence putty page (FAQ): 2 coats, pre-wet, no curing, 10–12 sq ft/kg, 1-year warranty, use within 12 months of manufacture.
  4. Birla White, SaltBlock brochure: 17–20 sq ft/kg for 2 coats, 360–380 ml water per kg, pot life 3–3.5 h.
  5. Birla White, SaltBlock warranty guide: treat damp first, 1:10 acid cleaning and rinse, 3–4 h between coats, about 24 h before primer, 500-grit sanding only, 1.5 mm limit, primer and paint within 30 days.
  6. Birla White, Best wall putty for salt stains (28 Aug 2026): how salt reaches the surface; ordinary putty is porous.
  7. Birla White, Wall putty work: step-by-step process (25 Sep 2026): 17–20 sq ft/kg for wall putty, 1.5 mm total.

Send us a photo of the patch

A close photo with a coin beside it, and one of the whole wall. We'll tell you where the water is coming from and what to buy, with today's price.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com