हिंदी Call90310 74624
Home›Guides›Sanitary and pipes
Building guide · toilet line

How a septic tank is built: two chambers, the inlet and outlet tees, the vent pipe and the cover

The short answer

Most houses in and around Muzaffarpur have no sewer, so the toilet line ends in a septic tank in the courtyard. It is a watertight brick box with two chambers. Toilet water comes in through a 110 mm tee that points down into the water. Solids settle and rot in the first, bigger chamber. Cleaner water passes through openings in the partition to the second chamber and leaves through a second tee, set 50 mm lower, to the soak pit. A vent pipe lets the gas out above the roof, and an RCC slab with a manhole over each chamber closes it.

2 : 1
First chamber to secondThe first holds twice as much: about ⅔ of the length.
50 mm
Outlet below inletSo water always moves forward, never back to the WC.
300 mm
Air under the slabRoom for scum and gas above the water.
Inside a septic tank
Cross-section of a two-chamber septic tankA brick tank in the ground under an RCC cover with two manholes. A 110 mm inlet tee from the toilet dips into the first chamber, which is two thirds of the length. A partition with openings below the water leads to the second chamber, one third of the length, and an outlet tee 50 mm lower takes the clear water to the soak pit. Scum floats on top, sludge settles on the floor, a vent pipe with a cowl lets gas out, and 300 mm of air is left under the slab. 300 mm air gap top water level scum sludge from toilet to soak pit vent, 50 mm or more to 2 m above the roof gas passes over ⅔ ⅓ 123456789 1Inlet tee110 mm, dips ~300 mm into water2First chamber⅔ of length: solids settle3Partitionopenings ~300 mm below water4Second chamber⅓ of length: finer settling5Outlet tee50 mm lower, dips ⅓ of depth6Vent pipemosquito mesh, cowl on top7RCC covera sealed manhole per chamber8Brick wall230 mm, 12 mm plaster both sides9Concrete floorM15, sloped, watertight
Not to scale. All figures from IS 2470 (Part 1): the Indian code for septic tanks. The partition stops short of the slab so gas from both chambers reaches one vent, as in the code's own sketch.
The parts

Eight parts, and what each one is for

The numbers match the drawing. Every size here is the code's figure; where the code says nothing, we say "usual practice".

1Inlet tee

Where the toilet line enters
  • A 110 mm SWR tee fixed inside the tank. The bottom leg goes about 300 mm below the water; the top leg stays open above the scum.
  • It drops new sewage gently below the scum without stirring the sludge (IS 2470 cl. 3.4.5.4).
  • 110 mm SWR tee and pipe

2First chamber

⅔ of the length
  • Heavy solids sink and become sludge; grease and paper float as scum. Bacteria slowly digest both.
  • The code keeps sewage in the tank for 24 to 48 hours.

3Partition wall

Between the chambers
  • Brick or concrete. Openings of 100 to 150 mm, about 300 mm below the water, so only the middle layer passes: not scum, not sludge (cl. 3.4.6).
  • Set it so the first chamber holds twice the second.

4Second chamber

⅓ of the length
  • Finer solids settle here, so the water that leaves is clearer and the soak pit lasts longer.

5Outlet tee

Out to the soak pit
  • A 110 mm tee whose bottom leg reaches about ⅓ of the water depth. Its invert sits 50 mm below the inlet's (cl. 3.4.5.5).
  • This pipe sets the water level of the whole tank.

6Vent pipe

Lets the gas out
  • At least 50 mm, with a mosquito-proof mesh cage at the top (cl. 3.4.10).
  • About 2 m high if the tank is 20 m or more from any building; if closer, which is nearly every plot here, 2 m above the top of the building.
  • Vent cowl

7RCC cover and manholes

Closes the tank
  • One opening per chamber, at least 455 × 610 mm or 500 mm round, with an RCC or cast-iron cover that lifts and seals (cl. 3.4.9).
  • Slab top a little above the yard so rain runs off it.

8Walls and floor

Must hold water both ways
  • Brick walls at least 200 mm (a 9-inch wall is fine), plastered 12 mm inside and outside in cement mortar no weaker than 1:3 (cl. 4.2.2).
  • Floor of M15 concrete or better, sloped about 1 in 10 towards the end the sludge is drawn from (cl. 4.1.1).
How it works

Three things happen inside, and the tees protect all three

A septic tank is not a pit that fills up. It is a slow settling tank that stays full to its outlet all the time.

1Settle

Heavy matter sinks to the floor as sludge. That is why the floor must be watertight and why the outlet takes water from the middle, never the bottom.

2Float

Grease, soap and paper rise as scum. It looks bad but it keeps the smell in. The tees reach below it, so the scum never leaves the tank and never reaches the soak pit.

3Digest

Bacteria with no air break the sludge down, which is what makes it smaller and gives off the gas. Large amounts of phenyl, acid, bleach or detergent kill them; the code warns against these.

What leaves the tank is not clean. It is settled, not treated. IS 2470 says it must never go into an open drain or a pond without further treatment. It goes to a soak pit, which lets the soil finish the job.

Where it goes

Where to put it on a Muzaffarpur plot

Where the tank goes on a plotPlan of a plot: house with the toilet at the back, a 110 mm line with a bend with door to the septic tank in the open courtyard, then to the soak pit in the far corner. The soak pit is at least 6 m from the house and at least 18 m from the boring. The tanker on the lane must reach the manholes. LANE TANKER HOUSE WC septic tank soak pit boring 18 m or more (IS 2470-2) 6 m or more bend with door Tank in the open: not under a room, away from the wall, tanker can reach it.
Not to scale. Distances for the soak pit from IS 2470 (Part 2), cl. 5.3.
  • In the open, away from the house wall. The code wants the tank under the sky and as far from the building as the plot allows, never under a room or the stairs, and reachable for cleaning (cl. 3.3.1).
  • Not in the low, wet corner. The code says not in swampy or flood-prone spots. If the yard floods, raise the slab top above that water; see how high to raise the plinth.
  • The boring is the main worry. The 18 m rule is for the soak pit, the part that lets water into the ground. On a small plot that is rarely possible, so keep the pit and the boring at opposite corners. Both are covered in where to put the boring and the soak pit guide.
  • A straight, gently falling line from the toilet. 100 mm pipe at least (we use 110 mm SWR). Long bends with a cleaning door where it turns, and branches joining at no more than 45°. The last 12 m before the tank no steeper than 1 in 50, so the water does not churn the tank. Pipe sizes and falls: connecting the toilet to the tank.
  • Leave a way in for the tanker. A suction tanker on the lane must get its hose to both manholes.
The Muzaffarpur problem: water close below the ground.The Central Ground Water Board's district booklet for Muzaffarpur measured water levels between about 0.7 m and 7.6 m below ground across the district, shallowest after the monsoon. A tank 1.5 to 2 m deep can sit in ground water from August to October. So dig and build between February and May, make the walls and floor truly watertight so ground water cannot get in and sewage cannot get out, and plan cleaning before the rains.
Build order

Nine steps, from digging to the first flush

The tees are set while the walls go up, not cut in later. The drawing shows the levels the mason must hit.

Levels of the inlet and outlet teesThe inlet pipe enters 50 mm higher than the outlet pipe. The outlet invert sets the top water level. The inlet tee dips about 300 mm below that level; the outlet tee dips one third of the liquid depth D, which is at least 1 m. At least 300 mm of air is left between the water and the slab. Both tees are open at the top, above the scum. ≈ 300 mminlet dip ⅓ of Doutlet dip 300 mm or moreair under the slab 50 mm inlet invert TWL = outlet invert D1 m or more open tops, above scum sludge INLETOUTLET Not to scale. Figures from IS 2470 (Part 1), clauses 3.4.5 to 3.4.8.
StepWhat to do
1. Mark and digInside size from your size, plus 230 mm walls each side and working space. Dig in the dry months; keep the sides from falling in.
2. FloorConcrete of M15 or better (IS 2470's sketch uses 1:2:4), usually 150 mm thick, sloped about 1 in 10 towards the end the sludge is drawn from. At most 25 L of water per 50 kg bag.
3. Walls and partition9-inch brick walls in cement mortar. Leave the partition openings, 100–150 mm, about 300 mm below the future water level.
4. Set the teesBuild the inlet and outlet pipes into the walls as you go. Check with a level pipe that the outlet invert is 50 mm lower than the inlet invert.
5. Plaster12 mm, cement mortar 1:3, inside and outside. Add Weather Pro WP+200 (200 ml per bag) to the inside plaster; give the floor-to-wall corner a coat of Seal & Dry SBR slurry first.
6. Cure and testKeep it wet at least 7 days (10 days with PPC or slag cement, IS 456). Then fill it with water to the outlet and watch the level for a day: it must not drop.
7. Cover slabRCC with a manhole frame over each chamber. Usual practice: about 125 mm thick, 8 mm bars both ways at about 150 mm. If a car or tractor will cross it, have an engineer design it.
8. Vent and backfillVent pipe up to 2 m above the roof, mesh and cowl on top. Backfill around the walls in layers; slab top above the yard.
9. Start itJoin the toilet line only when everything is complete. Keep the tank full of water to the outlet; the code suggests adding a little well-rotted cow dung if no sludge from an old tank is at hand.
What goes wrong

Six mistakes we hear about from customers

scumplain pipe: scum leaves

Plain pipe in place of the outlet tee

The soak pit chokes in a year or two

A straight pipe at the water line skims off the scum and sends it to the soak pit, which clogs with grease. A tee reaching below the scum costs very little.

outletbacks up to the WC

Outlet set higher than the inlet

Water stands in the house line; the WC drains slowly

The water level rises above the inlet pipe and the line from the house stays full and silts up. Outlet invert 50 mm below the inlet, always.

bathroomno vent

No vent, or a vent cut off at the slab

Smell from the bathroom floor trap

The gas has to go somewhere. Without a vent it pushes back up the line and through any trap with a weak water seal. See why traps smell.

rain pipetank overflows

Roof rainwater piped into the tank

Overflows in July and flushes sludge out

The code says no surface water may reach the tank. A rain pipe fills it in minutes and pushes sludge into the soak pit. Rainwater goes to the yard drain.

open nalino soak pit

Outlet into the open nali

Untreated sewage in the lane

IS 2470 says septic tank water must never go into an open drain without treatment. It goes to a soak pit, or where the ground is waterlogged, to a filter the code describes in Part 2.

boringleaks into the soil

Bare brick walls and a kachcha floor

"It never fills" because it leaks

A tank that never fills is pouring raw sewage into the ground water your boring draws from. Walls plastered both sides, concrete floor, water test before use.

How big

The size comes from the number of people and how often you clean it

More users or longer gaps between cleanings mean a bigger tank. The full method, with house examples, is on the septic tank size page. The code's limits for any tank:

RuleIS 2470 (Part 1)
Inside width750 mm or more
Water depth1 m or more
Length2 to 4 × width
Capacity1,000 L or more
Air above water300 mm or more
UsersLength × widthWater depth, cleaned yearlyEvery 2 years
51.5 × 0.75 m1.0 m1.05 m
102.0 × 0.90 m1.0 m1.4 m
152.0 × 0.90 m1.3 m2.0 m
202.3 × 1.10 m1.3 m1.8 m

IS 2470 (Part 1), Appendix A, Table 5. Add 300 mm of air above the water depth. The code's note: these sizes assume only toilet water goes in. Bath and kitchen water make the tank fill and work worse, so the code sends them to their own soak pit or drain.

Material list

What your tank will take from the store

Type the inside size the mason or the size page gave you. The list covers the floor, walls, partition, plaster, cover slab and fittings, for a 9-inch brick tank built as above.

Holds about — litres of water, with 1 ft of air above.

6.5 × 3 ft with 4.5 ft of water is close to the code's 10-user tank cleaned every 2 years. Find your size.

Your list

Prices are from our latest bill and change often. Please confirm today's rate on WhatsApp or call before buying.

Bricks
—Walls 230 mm, partition 115 mm, about 500 per m³ plus 5% for breakageAsk today's rate
UltraTech PPC cement—Brickwork in 1:4 mortar and 12 mm plaster 1:3, both sidesAsk today's rate
UltraTech Premium cement—Floor 150 mm (1:2:4) and cover slab 125 mm (M20)Ask today's rate
Balu (sand)—Mortar, plaster and concreteAsk today's rate
Gitti—Floor and slab concreteAsk today's rate
Tata Tiscon 8 mm, cover slab——Ask today's rate
Weather Pro WP+200—200 ml per bag in the inside plasterAsk today's rate
110 mm SWR fittingsset2 single tees (inlet, outlet), 1 tee with door on the house line, 1 vent cowl, pipe for the legs and the vent, solventAsk today's rate
Material totalAsk rate
Send this list on WhatsApp

Our estimate from standard mix figures (cement 6.5 bags per m³ of M15 and 8.1 of M20, as on our slab pages), not a mason's measured bill. Add 5–10% for a rough site. Soak pit material is on the soak pit page. Cutting and delivery are charged separately; ask for the amount for your site (delivery).

After it is built

Cleaning, and the one rule that saves lives

When to clean

  • When scum and sludge together pass half the depth. For a house tank used by the number it was built for, at least once in 2 years (IS 2470 cl. 5.1).
  • Too often is also bad: it removes the bacteria.

How to clean

  • A suction tanker from the manhole. Leave about 25 mm of sludge as seed (cl. 5.2).
  • Plan it for April–May. Don't pump it bone dry in the monsoon, when ground water presses on the walls.

Nobody goes inside

  • The gas in a septic tank can kill in minutes, and people die every year going in to save someone who fell. The code itself says manual handling of sludge should be avoided.
  • Keep the manhole covers locked or heavy, away from children.
Questions people ask us

Short answers

How many chambers does a septic tank need? (septic tank me kitne chamber)

IS 2470 lets a tank above 2,000 litres be split into two chambers, with the first holding twice as much as the second. Small tanks may have one. Many masons here build three; that is fine as long as the first two follow these rules, but the extra chamber does not replace the soak pit.

Can bathing and kitchen water go into the septic tank?

The code sizes the tank for toilet water only and sends bath and kitchen water to a soak pit or drain of its own. Soap, detergent and grease in large amounts slow the bacteria, and the tank fills much faster.

Should the floor be left kachcha so the tank never fills?

No. IS 2470 asks for a watertight concrete floor and plastered walls. An open floor lets raw sewage into the same ground water your boring pumps up. The tank is meant to fill to its outlet; the treated water then goes to the soak pit.

How far should the septic tank be from the boring?

IS 2470 Part 2 puts the soak pit, the part that lets water into the soil, at least 18 m from any drinking-water source and at least 6 m from the house. The tank itself is sealed; keep it as far from the boring as the plot allows, in the open, away from the house wall. See where to put the boring.

How often does a septic tank need cleaning?

IS 2470 says small house tanks may be cleaned at least once in 2 years if not overloaded, and in general when scum and sludge together pass half the tank depth. Leave about 25 mm of sludge as seed. Use a suction tanker; do not empty it fully in the monsoon.

Can someone go inside a septic tank to clean or repair it?

No. The gas inside can kill in minutes, and people die every year going in to help someone who fell. Clean only with a suction tanker from the manhole. If a repair needs a person inside, the tank must be emptied, ventilated for a long time and entered only by a trained crew with breathing gear.

Is a separate vent pipe needed if the tank is joined to the soil pipe?

IS 2470 allows the tank to vent through the building's soil vent pipe instead. If it has its own vent, use at least 50 mm, put mosquito mesh and a cowl on top, and take it 2 m above the roof when the tank is within 20 m of the house.

Plastic ready-made septic tank or brick?

Both work the same way inside. A plastic tank is quick to fit but light, so in ground that floods it must be anchored as its maker says or it can lift when empty. We can order one for you; ask on WhatsApp for the time it takes.

Arun Tiwari
Thekedar · site work, costs and plumbing, Tashya Ventures

Twenty years on house sites around Muzaffarpur, many of them fixing tanks built with a plain pipe for an outlet or no vent at all. Every size on this page was read from IS 2470 (Parts 1 and 2) on 14 Nov 2026. Where the code is silent, as on the cover slab bars, the page says "usual practice"; the material list is our estimate from standard mix figures.

Where the numbers come from

  1. Bureau of Indian Standards, IS 2470 (Part 1): 1985, Code of practice for installation of septic tanks: design criteria and construction (reaffirmed 2001): 100 mm pipes, long bends with cleaning eyes, 45° junctions, last 12 m at 1:50 (3.1–3.2); location (3.3.1); 24–48 h detention (3.4.4); 750 mm, 1 m, 1,000 L, length 2–4 × width (3.4.5); inlet tee 300 mm, outlet tee ⅓ depth, 50 mm drop (3.4.5.4–5); partition 2:1, openings 100–150 mm at 300 mm (3.4.6); 300 mm free board (3.4.8); access 455 × 610 mm or 500 mm (3.4.9); vent 50 mm, mesh, height (3.4.10); M15 floor at 1:10, 200 mm brick walls, 12 mm 1:3 plaster (4.1–4.2); desludging (5); commissioning (6); Table 5.
  2. Bureau of Indian Standards, IS 2470 (Part 2): 1985, Secondary treatment and disposal of septic tank effluent: soak pit 18 m from drinking water, 6 m from buildings (5.3); filters for waterlogged ground (6).
  3. Central Ground Water Board, Ground water information booklet, Muzaffarpur district: depth to water 2011, about 0.7 to 7.6 m below ground.
  4. IS 456: 2000, curing at least 7 days, 10 days with blended cements. Concrete water at most 25 L per bag and cement per m³ as on our slab pages.

Send us your tank size

We'll send back the bricks, cement, sand, gitti, sariya and SWR fittings for it, with today's price, on WhatsApp.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com